Pioneer VSX-2021 Manuel d'utilisateur télécharger pdf (Page 72)

EXTENSION Setup

! Default setting: OFF

A separately sold the CU-RF100 can be used to

operate the receiver by RF communications. To

do so, set the EXTENSION setting to ON. When

ON is set here, the receiver can be operated

even when the receiver is in the standby mode.

1 Select ‘EXTENSION Setup’ from the

Other Setup menu.

2 Select the EXTENSION setting you

want.

3 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Software Update

Use this procedure to update the receiver’s

software and check the version. There are two

ways to update: via the Internet and via a USB

memory device.

Updating via the Internet is performed by

accessing the file server from the receiver and

downloading the file. This procedure is only pos-

sible if the receiver is connected to the Internet.

Updating via a USB memory device is per-

formed by downloading the update file from a

computer, reading this file onto a USB memory

device then inserting this USB memory device

into the USB port on the receiver’s front panel.

With this procedure, the USB memory device

containing the update file must first be inserted

into the USB port on the receiver’s front panel.

! If an update file is provided on the Pioneer

website, download it onto your computer.

When downloading an update file from the

Pioneer website onto your computer, the file

will be in ZIP format. Unzip the ZIP file before

saving it on the USB memory device. If there

are any old downloaded files or downloaded

files for other models on the USB memory

device, delete them.

Important

! DO NOT unplug the power cord during

updating.

! When updating via the Internet, do not

disconnect the LAN cable. When updating via

a USB memory device, do not disconnect the

USB memory device.

1 Select ‘Software Update’ from the

Other Setup menu.

2 Select the update procedure.

! Update via Internet – The receiver checks

whether updatable software is available via

the Internet.

! Update via USB Memory – The receiver

checks whether the USB memory device

inserted into the USB port on the receiver’s

front panel contains updatable software.

“Accessing” is displayed and the update file

is checked. Wait a while.

3 Check on the screen whether or not an

update file was found.

If “New version found.” is displayed, the

update file has been found. The version number

and updating time are displayed.

If “This is the latest version. There is no need

to update.” is displayed, no update file has

been found.

4 To update, select OK.

The updating screen appears and updating is

performed.

! The power turns off automatically once

updating is completed.

12 The System Setup and Other Setup menus

Volume Setup

You can set the maximum volume of this

receiver or specify what the volume level will be

when the power is turned on.

1 Select ‘Volume Setup’ from the

Other Setup menu.

2 Select the Power ON Level setting you

want.

The volume can be set so that it is always set

to the same level when the receiver’s power is

turned on.

! LAST (default) – When the power is turned

on, the volume is set to the same level as

when the power was last turned off.

! “---” – When the power is turned on, the

volume is set to minimum level.

! –80.0dB to +12.0dB – Specify the volume to

be set when the power is turned on, in steps

of 0.5 dB.

It is not possible to set a volume level greater

than the value specified at Volume Limit setup

(see below).

3 Select the Volume Limit setting you

want.

Use this function to limit the maximum volume.

The volume cannot be increased above the level

set here, even by operating MASTER VOLUME

button (or the dial on the front panel).

! OFF (default) – The maximum volume is not

limited.

! –20.0dB/–10.0dB/0.0dB – The maximum

volume is limited to the value set here.

4 Select the Mute Level setting you

want.

This sets how much the volume is to be turned

down when MUTE is pressed.

! FULL (default) – No sound.

! –40.0dB/–20.0dB – The volume will be

turned down to the level specified here.

5 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Remote Control Mode Setup

! Default setting: 1

This sets this receiver’s remote control mode

to prevent erroneous operation when multiple

units of the receiver are being used.

1 Select ‘Remote Control Mode Setup’

from the Other Setup menu.

2 Select the Remote Control Mode

setting you want.

3 Select ‘OK’ to change the remote

control mode.

4 Follow the instructions on the screen

to change the remote control’s setting.

See Operating multiple receivers on page 54 .

5 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Flicker Reduction Setup

! Default setting: OFF

The GUI screen’s resolution can be increased.

If you feel the GUI screen is hard to see, try

changing this setting. Note that the resolution

in this setting only affects the GUI screen; it has

no influence on the video output.

1 Select ‘Flicker Reduction Setup’ from

the Other Setup menu.

2 Select the Flicker Reduction setting you

want.

3 When you’re finished, press RETURN.

You will return to the Other Setup menu.

1 2 ... 67 68 69 70 71 72 73 74 75 76 77 ... 101 102

Commentaires sur ces manuels

Pas de commentaire

Pioneer VSX-2021 Manuel d'utilisateur Page 72

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de cinéma à domicile Pioneer VSX-2021