Pioneer VSX-2021 Manuel d'utilisateur télécharger pdf (Page 26)

04 Basic Setup

! Before using the Full Auto MCACC Setup, the

headphones should be disconnected.

CAUTION

! The test tones used in the Full Auto MCACC

Setup are output at high volume.

THX

! THX is a trademark of THX Ltd. which is

registered in some jurisdictions. All rights

reserved.

1 Press u RECEIVER to switch on the

receiver and your TV.

Make sure that the TV’s video input is set to this

receiver.

2 Connect the microphone to the MCACC

SETUP MIC jack on the front panel.

Push down on the lower portion of the front

panel door to access the MCACC SETUP MIC

jack.

PHONES

MULTI-ZONE

CONTROL ON/OFF

MCACC

SETUP MIC

USB

iPod iPhone iPad

AUTO SURR/ALC/

STREAM DIRECT

iPod iPhone iPad

DIRECT CONTROL

5V 2.1

Microphone

Tripod

Make sure there are no obstacles between the

speakers and the microphone.

If you have a tripod, use it to place the micro-

phone so that it’s about ear level at your

normal listening position. If you do not have

a tripod, use some other object to install the

microphone.

Install the microphone on a stable floor.

Placing the microphone on any of the following

surfaces may make accurate measurement

impossible:

! Sofas or other soft surfaces.

! High places such as tabletops and sofa tops.

The Full Auto MCACC display appears once the

microphone is connected.

Speaker System : Normal

(

SB/FH

)

1a.Full Auto MCACC

A/V RECEIVER

Exit Return

START

EQ Type : SYMMETRY

MCACC : M1.MEMORY 1

THX Speaker : NO

! If you leave the GUI screen for over five

minutes, the screen saver will appear.

3 Select the parameters you want to set.

! When data measurement is taken, the

reverb characteristics data (both before- and

after-calibration) that this receiver had been

storing will be overwritten.

! When measurement is taken of the reverb

characteristics data other than SYMMETRY,

the data are not measured after the

correction. If you will need to measure after

correcting data, take the measurement

using the EQ Professional menu in the

Manual MCACC setup (page 62).

If the speakers are connected using any setup

other than Normal(SB/FH), be sure to set

Speaker System before the Full Auto MCACC

Setup. See Speaker system setting on page 67 .

! Speaker System – Shows the current

settings. When this is selected and ENTER is

pressed, the speaker system selection screen

appears. Select the proper speaker system,

then press RETURN to return.

If you are planning on bi-amping your front

speakers, or setting up a separate speaker

system in another room, read through

Speaker system setting on page 67 and make

Basic Setup

Switching the speaker

impedance

We recommend using speakers of 8 W with this

system, but it is possible to switch the imped-

ance setting if you plan to use speakers with a 6

W impedance rating.

1 Switch the receiver into standby.

2 While holding down ENTER on the

front panel, press u STANDBY/ON.

The display shows RESET c NO d.

3 Use TUNE i/j to select SPEAKER c

8W d, and then use PRESET k/l to select

SPEAKER 8W or SPEAKER 6W.

! SPEAKER 8W – Use this setting if your

speakers are rated at 8 W or more.

! SPEAKER 6W – Use this setting if your

speakers are rated at 6 W.

Changing the OSD display

language (OSD Language)

The language used on the Graphical User

Interface screen can be changed.

! The explanations in these operating

instructions are for when English is selected

for the GUI screen.

1 Press u RECEIVER to switch on the

receiver and your TV.

Make sure that the TV’s video input is set to

this receiver (for example, if you connected this

receiver to the VIDEO jacks on your TV, make

sure that the VIDEO input is now selected).

2 Press on the remote control,

then press HOME MENU.

A Graphical User Interface (GUI) screen

appears on your TV. Use i/j/k/l and

ENTER to navigate through the screens and

select menu items. Press RETURN to exit the

current menu.

3 Select ‘System Setup’ from the Home

Menu.

4 Select ‘OSD Language’ from the

System Setup menu.

5 Select the desired language.

6 Select ‘OK’ to change the language.

The setting is completed and the System Setup

menu reappears automatically.

Automatically conducting

optimum sound tuning (Full

Auto MCACC)

The Full Auto MCACC Setup measures the

acoustic characteristics of your listening area,

taking into account ambient noise, speaker

connection and speaker size, and tests for both

channel delay and channel level. After you have

set up the microphone provided with your sys-

tem, the receiver uses the information from a

series of test tones to optimize the speaker set-

tings and equalization for your particular room.

By performing the Full Auto MCACC Setup

procedure, the frequency-phase characteristics

of the connected speakers are also calibrated.

Once the Full Auto MCACC Setup procedure is

completed, the Full Band Phase Control func-

tion is automatically turned on (page 38).

Important

! Make sure the microphone and speakers are

not moved during the Full Auto MCACC Setup.

! Using the Full Auto MCACC Setup will

overwrite any existing settings for the MCACC

preset you select.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 101 102

Commentaires sur ces manuels

Pas de commentaire

Pioneer VSX-2021 Manuel d'utilisateur Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de cinéma à domicile Pioneer VSX-2021