Pioneer SC-LX88-K Manuel d'utilisateur télécharger pdf (Page 8)

Initial Setup

Before you start

Put the batteries in the remote control.

The batteries included with the unit are to check initial

operations; they may not last over a long period. We

recommend using alkaline batteries that have a longer life.

Switch on the receiver and your TV.

ALL ZONE STBY

SOURCE

STANDBY/ON

MAIN

SUB ZONE CONTROL

Z2 Z3 HDZ

RECEIVER

Switch the TV input so that it connects to the

receiver.

Turn the subwoofer on and turn up the volume.

WARNING

• Do not use or store batteries in direct sunlight or other

excessively hot place, such as inside a car or near a heater.

This can cause batteries to leak, overheat, explode or catch

fire. It can also reduce the life or performance of batteries.

CAUTION

• When inserting the batteries, make sure not to damage

the springs on the battery’s (–) terminals. This can cause

batteries to leak or overheat.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

institution’s rules that apply in your country/area.

Automatically setting up for

surround sound (MCACC)

The Auto Multi-Channel ACoustic Calibration (MCACC) setup

uses the supplied setup microphone to measure and analyze

the test tone that is outputted by the speakers. This setup

enables automatic high precision measuring and settings;

utilizing it will create an optimum user listening environment.

Important

• Measure in a quiet environment.

• If you have a tripod, use it to place the microphone so that it’s

about ear level at your normal listening position. Otherwise,

place the microphone at ear level using a table or a chair.

• Accurate measurements may not be possible if there are

obstacles between the speakers and the listening position

(microphone).

• When measuring, step away from the listening position,

and operate using the remote control from the external

side of all the speakers.

Connect the supplied setup microphone.

MASTER

VOLUME

STANDBY/ON

INPUT

SELECTOR

iPod iPhoneHDMI

MCACC PRO

FL OFF

MCACC

SETUP

MIC

Tripod

Microphone

The

Full Auto MCACC

screen appears on your TV.

Speaker System : 7.2.2ch TMd/FW

1a.Full Auto MCACC

A/V RECEIVER

Exit Return

START

EQ Type : – – –

SP to ceiling : 3.00m

MCACC : M1.MEMORY 1

Dolby Enabled Speaker

: NO

Measurement Type : Basic

Press MAIN RECEIVER on the remote control

and operate.

• When the cursor is brought to

Measurement Type

and

Basic

is selected, the

Speaker Setting

Channel Level

Speaker Distance

is adjusted automatically. Selecting

Expert

allows you to automatically adjust

Standing

Wave

Acoustic Cal EQ

(frequency characteristics)/

Full

Band Phase Control

as well.

Bring the cursor to START and press the ENTER

button.

• Automatic measuring will start.

• Measuring will take about 3 to 12 minutes.

Follow the instructions on-screen.

• Automatic setting is complete when the Home Menu

screen appears.

1. MCACC PRO

2. MCACC Data Check

3. Data Management

4. System Setup

5. Network Information

6. Operation Mode Setup

Exit Return

HOME MENU

A/V RECEIVER

• If

Reverse Phase

is displayed, the speaker’s wiring (+ and –)

may be inverted. Check the speaker connections.

Even if the connections are correct,

Reverse Phase

may be

displayed, depending on the speakers and the surrounding

environment. This does not affect measurements, however,

so select

Go Next

• If the power cuts out, the core of the speaker cable may be

in contact with the rear panel, or the (+) and (–) cores may

be touching, causing the protection circuits to activate.

Re-twist the core of the speaker cable, and connect it so

that it does not protrude from the speaker terminal.

Make sure the setup microphone is

disconnected.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 75 76

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX88-K Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de cinéma à domicile Pioneer SC-LX88-K