Pioneer SC-LX57-S Manuel d'utilisateur télécharger pdf (Page 79)

Using other functions

Using the sleep timer

The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without

worrying about the receiver being left on all night. Use the remote control to set the sleep timer.

% Press to the receiver operation mode, then press SLEEP repeatedly to set the sleep

time.

30 min 60 min

Off 90 min

! You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle

through the sleep options again.

! The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning.

Dimming the display

You can choose between four brightness levels for the front panel display. Note that when selecting sources, the

display automatically brightens for a few seconds.

% Press to the receiver operation mode, then press DIMMER repeatedly to change the

brightness of the front panel display.

! You can also choose to turn the display off. In this case, the FL OFF indicator lights.

Switching the HDMI output

Set which terminal to use when outputting video and audio signals from the HDMI output terminals.

The HDMI OUT 1 terminal is compatible with the Control with HDMI function.

1 Press to the receiver operation mode, then press HDMI OUT.

2 Use i/j to select OUT 1/2.

3 Use k/l to select the output settings for the HDMI OUT 1 and HDMI OUT 2 terminals.

Please wait a while when Please wait ... is displayed.

The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed.

! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchro-

nized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV’s remote

control.

4 Use i/j to select OUT 3.

5 Use k/l to select the output settings for the HDMI OUT 3 terminal.

Please wait a while when Please wait ... is displayed.

The setting switches between ON and OFF each time this is pressed.

! When MAIN/HDZONE is set to HDZONE, the output of the HDMI OUT 3 terminal cannot be switched (page

103).

! Only signals input in HDMI format can be played with the HDMI OUT 3 terminal.

6 When you’re finished, press RETURN.

About the Speaker B Link function

When 7.1ch + Speaker B or 5.1ch + SP-B Bi-Amp is selected for the Speaker System setting (page 97) and

Speaker B Link (HDMI Setup on page 69) is set to “ON”, the setting of the speaker terminals that are played

changes automatically when HDMI OUT 1 and HDMI OUT 2 are switched. The setting switches as follows.

! OUT 1+2 – Switches to SP: A+B ON. Sound is output simultaneously in the room where the A speakers are

located and in the room where the B speakers are located.

! OUT 1 – Switches to SP: A ON. Sound is only output in the room where the A speakers are located.

! OUT 2 – Switches to SP: B ON. Sound is only output in the room where the B speakers are located.

Checking your system settings

Use the status display screen to check your current settings for features such as surround back channel process-

ing and your current MCACC preset.

1 Press to the receiver operation mode, then press STATUS.

2 Use i/j to check the system setting.

The information on the main unit display switches as shown below each time one of the buttons is pressed.

Audio format f Sampling frequency f MCACC memory f Auto phase control plus correction value f

Input source to be played in ZONE 2 f Input source to be played in ZONE 3 f Input source to be played in the

HDZONE f HDMI output setting f Subzone to which the HDZONE is output

! For some settings, some items are not displayed.

3 When you’re finished, press STATUS again to switch off the display.

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 133 134

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX57-S Manuel d'utilisateur Page 79

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de cinéma à domicile Pioneer SC-LX57-S