Pioneer HTP-710 Manuel d'utilisateur Page 88

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 272
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 87
Additional information10
88
En
USB messages
Resetting the main unit
Use this procedure to reset all the system’s
settings to the factory default. Use the front
panel controls to do this.
1 Switch the system into standby.
2 While holding down the
ST/MONO
button, press and hold the
STANDBY/ON
button for about two seconds.
3 When you see RESET? appear in the
display, press
TUNE –
.
OK? shows in the display.
4Press
TUNE +
to confirm.
OK appears in the display to indicate that the
system has been reset to the factory settings.
Specifications
SX-SWR2 Receiver subwoofer
Audio section
Rated power output
Front, Center, Surround . . .100 W per channel
(1 kHz, 4
Ω
, 10 %)
Subwoofer . . . . . . . . 100 W (100 Hz, 4
Ω
, 10 %)
FM tuner Section
Frequency Range. . . . . . . . .87.5 MHz to 108 MHz
Antenna Input . . . . . . . . . . . . . . 75 Ω unbalanced
Input/Output section
HDMI terminal:
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-pin x3
Output. . . . . . . . . . . . . . . . .19-pin (5 V, 100 mA)
Audio input. . . . . . Coaxial x1, Optical x2 (Digital)
RCA (2-pin) x4 (Analog)
Audio output . . . . . . . . . .RCA (2-pin) x2 (Analog)
Video input . . . . . . . . . . . . . . . . . . . . . . . . . RCA x3
Video output . . . . . . . . . . . . . . . . . . . . . . . . RCA x2
MCACC input . . . . . . . . . . . . . . . . . . . . . .Mini jack
iPod terminal . . . . . . . USB + Video (Composite)
Speaker section
Enclosure . . . . . . . . . . . . . . . Bass-reflex floor type
System . . . . . . . . . . . . . . . . . .16 cm 1-way system
Speakers. . . . . . . . . . . . . . . . . 16 cm cone type x1
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Ω
Frequency range . . . . . . . . . . . . 35 Hz to 1 000 Hz
Symptom Cause Action
iPod/USB Error 1
(I/U ERR1)
There is a problem with the signal path
from the USB to the system.
Switch off the system and reconnect the
USB to the system.
iPod/USB Error 3
(I/U ERR3)
When there is no response from the
USB.
Switch off the system and reconnect the
USB to the system.
iPod/USB Error 4
(I/U ERR4)
The power requirements of the USB
device are too high for this system.
Switch off the system and reconnect the
USB to the system.
HTP-710_VYXCN_En.book 88 ページ 2010年8月23日 月曜日 午後6時47分
Vue de la page 87
1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 271 272

Commentaires sur ces manuels

Pas de commentaire