Pioneer CNDV-100MT Manuel d'utilisateur télécharger pdf (Page 5)

The following messages are added to those of AVIC-X1R (CNDV-50MT):

Message When What to do

This area does not contain any

POI’s of the selected type.

Vicinity Search cannot be per-

formed because the searched loca-

tion is in areas not stored on the

DVD Map Disc.

Replace the DVD Map Disc and per-

form Vicinity Search again.

This country is not available on

the disc. Please insert an appropri-

ate disc.

When countries not stored on the

DVD Map Disc are included in the

search.

Set the destination or way point(s) in

the countries stored on the DVD

Map Disc, or replace the DVD Map

Disc and perform the search again.

Failed to make the route profile. Failed to generate the route profile

because the set route passes

through areas not stored on the DVD

Map Disc.

Insert the DVD Map Disc and retry.

No route data can be stored. You

should insert the disc that con-

tains the map data of the current

position.

The area to be set for [Map in Mem-

ory]is“areas not stored on the DVD

Map Disc”.

• Change the memory area to be set

to “areas stored on the DVD Map

Disc”.

• Insert the DVD Map Disc contain-

ing that area.

•Scaling down.

•Scaling up.

In the memory navi mode, if the DVD

Map Disc is inserted without chan-

ging the scale (only when the point

is stored on the DVD Map Disc).

The scale automatically returns to

the scale that was set in the DVD

navi mode before being changed to

the memory navi mode.

• No map data available on this

scale. Scaling up.

• No map data available on this

scale. Scaling down.

When the scale that had been pre-

viously displayed cannot be dis-

played for the following reasons:

• The disc was ejected and the sys-

tem was changed to the memory

navi mode.

• In the memory navi mode, the map

was scrolled to outside the memory

area. Or, the vehicle moved outside

of the memor y area.

• The map was scrolled to areas not

stored on the DVD Map Disc. Or, the

vehicle moved to unrecorded areas.

• The map was scrolled from unrec-

orded areas to the memory area. Or,

the vehicle moved from unrecorded

areas to the memory area.

If the desired scale cannot be se-

lected, insert the DVD Map Disc that

contains that area and then change

the scale.

Failure in the memory recovery

process. Memory navigation is

presently not possible.

Failed to complete the recovery of

the memory area because the disc

could not be read for some reason,

resulting in deletion of the memory.

• Clean the disc.

• Clean the DVD drive.

• Consult the Pioneer Local dealer if

this message persists.

This function is not available with

the current map disc.

The current position is “areas not

stored on the DVD Map Disc” and an

attempt was made to zoom in to

make the scale 500 m or more.

Zoom in again after the vehicle

moves into an area stored on the

DVD Map Disc.

Or, replace the DVD Map Disc and

try to zoom in again.

<CRB3461-A>17

Messages and how to

react to them

The programme is installed to the navigation

system using the application disc.

When installing the programme, you carry out

the following operations. When all the setup

procedures are completed, you can use the

navigation system.

The screen images used in this section are

AVIC-X1R as an example.

CAUTION

You cannot go back to the previous (pre-

upgrade) version of the application after

the software upgrade is completed. Also,

the map discs that were previously used

cannot be used. Instead, use the CNDV-

100MT DVDs as your new map discs.

1 Park your vehicle in a safe place.

Leave the engine on, and make sure that the

handbrake is applied.

2 Press EJECT button to remove the cur-

rent disc.

3 Insert the new Pioneer DVD Map Disc

into the appropriate slot.

When the upgraded programme has been

found, installation of the programme starts im-

mediately.

p If you cannot insert a disc completely or if

an inserted disc is not recognised, check

that the label side of the disc is up. Press

EJECT button to eject the disc, and check

the disc for damage before inserting the

disc again.

CAUTION

While this screen is visible, NEVER switch the

ignition key position or turn off the power of na-

vigation system.

When the installation is complete, the openin g

display appears.

p By upgrading AVIC-X1 or AVIC-X1BT with

these discs, the same screen appears.

p By upgrading other models with these

discs, the following opening display ap-

pears.

<CRB3461-A>18

Instructions for

upgrading

4 Press the NAVI/AV button to change

the navigation screen.

Some time is needed until navigation is ready.

5 Check the details of the caution mes-

sage and touch [OK].

The map of your surroundings is displayed.

You can operate the navigation system by

touching keys displayed on the screen as

usual.

When upgrading AVIC-X1, perform the following pro-

cedure.

6 To set the time difference, touch [+] or

[–].

Time difference

The time difference between the time origin-

ally set in the navigation system (Central Eur-

opean Time) and the current location of your

vehicle is shown. If necessary, adjust the time

difference. Touching [+]or[–] changes the

time difference display in one-hour incre-

ments. The time difference can be set from +3

to –3 hours.

7 If necessary, set to summer time.

Summer time setting is off by default. Touch

[Summer Time] to change the setting if you

are in the summer time period.

8 To complete the setting, touch [Back].

The map of your surroundings appears.

<CRB3461-A>19

<CRB3461-A>20

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Pioneer CNDV-100MT Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Multimédia automobile Pioneer CNDV-100MT