Pioneer SC-LX79 Manuel d'utilisateur télécharger pdf (Page 128)

128

FAQ

USB-DAC

SC-LX89 only

Symptoms Causes Remedies

When the USB-DAC IN

terminal is connected to

a PC via USB cable, audio

files on the PC cannot be

played.

Has the proper device driver been

installed on the PC?

When using a USB cable to connect the unit’s USB-DAC

IN terminal to a PC in order to play audio files on the PC,

the proper device driver must be downloaded from the sup-

plied CD-ROM and installed on your PC.

No sound is produced when

attempting to play files on

a PC.

Are volume settings correct for the

OS and application program?

Raise the volume settings as required.

Is the OS audio output set to MUTE? Cancel the MUTE setting.

Are multiple applications running

simultaneously?

Try closing applications that are not in use.

Are volume settings correct for the

OS and application program?

For audio device select “Pioneer USB Audio Device”.

High sound quality files

(over 48 kHz/24 bits) cannot

be played.

The exclusive driver is not installed

on the computer.

Install the driver software on the computer from the

included CD-ROM.

Wireless LAN

Symptoms Causes Remedies

Network cannot be

accessed via wireless LAN.

SSID uses double-byte characters

such as in the Japanese language.

This receiver is compatible only with single-byte alphanu-

merical characters and some symbols such as the under-

bar. If characters other than these are used, change the

SSID before executing network settings. Refer to the user’s

manual for your router for information on SSID.

There is distance or obstacles

between this receiver and equipment

including the wireless LAN router.

Improve the wireless LAN environment such as making the

distance between this receiver and equipment including

wireless LAN router closer.

There is a microwave oven or other

device generating electromagnetic

waves near the wireless LAN envi-

ronment.

Use the system in a place away from microwave ovens or

others device generating electromagnetic waves.

Avoid using devices generating electromagnetic waves as

much as possible when using the system with the wireless

LAN.

Multiple devices are connected to

the wireless LAN router.

When connecting multiple devices to the wireless LAN

router, the IP address of the connected devices must be

changed.

The wireless LAN connection set-

tings of this receiver and equipment

such as wireless LAN router is not

correct.

When wireless LAN connections for this receiver and wire-

less LAN router are not setup, the connection between this

receiver and equipment such as the wireless LAN router

must be set.

The IP address settings of this

receiver do not match the settings of

the wireless LAN router and the like.

Check the IP address settings (including DHCP settings)

of this receiver.

If the receiver’s DHCP setting is “ON”, turn the receiver’s

power off, then turn the power back on.

Check that the IP address for this receiver matches the

settings of the wireless LAN router.

If the receiver’s DHCP setting is “OFF”, set an IP address

matching the network of the base unit (wireless LAN

router, etc.).

For example, if the wireless LAN router’s IP address

is “192.168.1.1”, set the receiver’s IP address to

“192.168.1.XXX” (*1), the subnet mask to “255.255.255.0”,

the gateway and DNS to “192.168.1.1”.

(*1) Set the “XXX” in “192.168.1.XXX” to a number between

2 and 248 that is not assigned to other devices.

The access point is set to conceal

the SSID.

In this case, it may not be shown in the access point list

screen. If it is not shown, set the SSID etc. of this receiver.

The access point’s security settings

use WEP 152-bit length code key or

shared key authentication.

The receiver does not support WEP 152-bit length code key

or shared key authentication.

There is a possibility that the chan-

nel used by the wireless network is

a wireless channel that cannot be

used with this receiver.

Change the wireless network channel to a wireless channel

that can be used with this receiver, then check the con-

nection.

Wireless Direct is not

connected when the main

power of this receiver is

turned off once and turned

on again.

The Security Protocol is set to

None.

Because there are security risks, settings are necessary to

connect to Wireless Direct again. Set Security Protocol of

Wireless Direct to WEP (page 58 ).

1 2 ... 123 124 125 126 127 128 129 130 131 132 133 ... 150 151

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX79 Manuel d'utilisateur Page 128

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer SC-LX79