Pioneer SC-LX59 Manuel d'utilisateur télécharger pdf (Page 118)

118

FAQ

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong

with this component, check the points below. Sometimes the trouble may lie in another component. Investigate

the other components and electrical appliances being used. If the trouble cannot be rectified even after exercis-

ing the checks listed below, ask your nearest Pioneer authorized independent service company to carry out repair

work.

! If the unit does not operate normally due to external effects such as static electricity disconnect the power plug

from the outlet and insert again to return to normal operating conditions.

If the problem is not solved after the troubleshooting below, if the screen freezes unexpectedly or if the buttons on

the remote control or front panel stop working completely, do the following:

! Press u STANDBY/ON on the front panel to turn off the power, then turn the power back on.

If this does not solve the problem, turn off the power again, then press and hold the u STANDBY/ON button

on the front panel for at least five seconds. (The power turns on, then turns off after five seconds.)

! If the power cannot be turned off, press and hold u STANDBY/ON on the front panel for over five seconds. The

power will turn off. In this case, the various settings made on the receiver may be cleared.

Power

Symptom Remedy

The power does not turn on. Make sure that the power cord is plugged in to an active power outlet.

Try disconnecting from the power outlet, then plugging back in.

Power automatically turns off.

When Auto Power Down is set, the power automatically turns off at the set time (page 113 ).

When the power is turned on, the

WIRELESS indicator slowly flashes.

After unpacking, turning on the power, and returning to initial factory settings (page 95 ),

the WIRELESS indicator slowly flashes. This is not a malfunction.

This receiver is designed to automatically enter WAC mode when turning on the power of

this receiver in the initial factory settings state. For details about WAC mode, please refer

to page 53 . After the network settings (page 51 ) have been completed, the WIRELESS

indicator flashing disappears.

When using the receiver without connecting to the network, set the Network Type set-

ting to Wired (page 52 ).

Power cannot be turned off.

(ZONE 2 ON is displayed.)

Press the Z2 button on the remote control for 1.5 seconds and then press the

u STANDBY/ON button to turn OFF the power.

Power cannot be turned off.

(ZONE 3 ON is displayed.)

Press the Z3 button on the remote control for 1.5 seconds and then press the

u STANDBY/ON button to turn OFF the power.

Power cannot be turned off.

(HDZONE ON is displayed.)

Press the HDZ button on the remote control for 1.5 seconds and then press the

u STANDBY/ON button to turn OFF the power.

The receiver suddenly switches off or

the WIRELESS indicator blinks.

Check that there are no loose strands of speaker wire touching the rear panel or another

set of wires. If so, re-attach the speaker wires, making sure there are no stray strands.

The receiver may have a serious problem. Disconnect from the power and call a Pioneer

authorized independent service company.

Symptom Remedy

During loud playback the power sud-

denly switches off.

Turn down the volume.

Lower the 63 Hz and 125 Hz equalizer levels in the Manual MCACC setup on page 105 .

Switch on the digital safety feature. While holding down ENTER on the front panel,

press u STANDBY/ON to set this receiver to the standby mode. Use TUNE i/j to

select D.SAFETY cOFFd, and then use PRESET k/l to select 1 or 2 (select D.SAFETY

cOFFd to deactivate this feature). If the power switches off even with 2 switched on, turn

down the volume. With 1 or 2 on, some features may be unavailable.

If there is very little low frequency information in the source material, change your

speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS

(see Speaker Setting on page 111 ).

The unit does not respond when the

buttons are pressed.

Try switching the receiver off, then back on again.

Try disconnecting the power cord, then connect again.

AMP ERR is indicated and the main

power turns off. The MCACC PRO

indicator blinks and the main power

does not turn on.

The receiver may have a serious problem. Do not try switching the receiver on. Unplug

the receiver from the wall and call a Pioneer authorized independent service company.

The receiver suddenly switches off or

the FL OFF indicator blinks.

There is a possibility that the power supply circuit of the receiver has failed. Wait at least

one minute and then turn ON the power again. If the same symptom appears again after

turning ON the power again, stop using the receiver, disconnect the power cable and

request repair.

AMP OVERHEAT blinks in the dis-

play and the FL OFF indicator flash

and the power turns off.

Allow the unit to cool down in a well-ventilated place before switching back on (see

Installing the receiver on page 10 ).

Check whether the cables used to connect the speakers are short-circuited.

Wait at least 1 minute, then try turning the power on again.

The temperature within the unit has exceeded the allowablevalue.

Lower the volume level.

The main power suddenly turns off,

and MCACC PRO indicator blinks.

The power unit is damaged. Unplug the receiver from the wall and call a Pioneer autho-

rized independent service company.

FAN STOP is displayed, then

WIRELESS indicator blinks.

The built-in cooling fan is malfunctioning. Do not try switching the receiver on. Unplug

the receiver from the wall and call a Pioneer authorized independent service company.

Display blinks 12V TRG ERR. An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power

back on.

No sound

Symptom Remedy

There is no sound output, the sound

gets cut off, or there is noise present.

If Fixed PCM in audio parameter is set to ON, you will not be able to playback audio in

formats other than PCM audio. For other audio formats than PCM audio, select OFF (See

Setting the Audio options on page 87 ).

No sound is output when an input

function is selected.

Turn the volume up to approx. –30 dB.

Check that the speaker selector setting is set to OFF (page 91 ).

Make sure the correct input function is selected.

Make sure the correct input signal is selected (see Choosing the input signal on page 73 ).

Check that the source equipment is correctly connected (see Connecting your equipment

on page 18 ).

Check that the speakers are connected properly (see Connecting the speakers on page 25 ).

1 2 ... 113 114 115 116 117 118 119 120 121 122 123 ... 148 149

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX59 Manuel d'utilisateur Page 118

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer SC-LX59