Pioneer SC-LX59 Manuel d'utilisateur télécharger pdf (Page 112)

112

The System Setup and Other Setup menus

Channel Level

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor

when setting up a home theater system.

1 Select ‘Channel Level’ from the Manual SP Setup menu.

The test tones will start.

2 Adjust the level of each channel using k/l.

Use i/j to switch speakers.

Adjust the level of each speaker as the test tone is emitted.

! If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and

adjust the level of each speaker to 75 dB SPL (C-weighting/slow reading).

3 When you’re finished, press RETURN.

You will return to the Manual SP Setup menu.

Speaker Distance

For good sound depth and separation from your system, you need to specify the distance of your speakers from

the listening position. (When Dolby Enabled Speaker is used, specify the distance reached by the speaker sound

reflected at the ceiling (page 20 ).) The receiver can then add the proper delay needed for effective surround

sound.

1 Select ‘Speaker Distance’ from the Manual SP Setup menu.

2 Adjust the distance of each speaker using k/l.

You can adjust the distance of each speaker in 0.01 m increments.

3 When you’re finished, press RETURN.

You will return to the Manual SP Setup menu.

Note

For best surround sound, make sure the surround back speakers are the same distance from the listening

position.

X-Curve

Most soundtracks mixed for cinema sound too bright when played back in large rooms. The X-Curve setting acts

as a kind of re-equalization for home theater listening, and restores proper tonal balance of movie soundtracks.

1 Select ‘X-Curve’ from the Manual SP Setup menu.

2 Choose the X-Curve setting you want.

Use k/l to adjust the setting. The X-Curve is expressed as a downwards slope in decibels per octave, starting

at 2 kHz. The sound becomes less bright as the slope increases (to a maximum of –3.0dB/oct). Use the following

guidelines to set the X-Curve according to your room size:

Room size (

)

X-Curve

(dB/oct)

–0.5 –1.0 –1.5 –2.0 –2.5 –3.0

≤36 ≤48 ≤60 ≤72 ≤300 ≤1000

! If you select OFF, the frequency curve will be flat and the X-Curve has no effect.

3 When you’re finished, press RETURN.

MHL Setup

Select whether or not to switch the input automatically to the MHL input when an MHL-compatible device is

connected.

! Default setting: ON

1 Press MAIN RECEIVER to switch the remote control to the receiver operation mode, and

then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the

screens and select menu items. Press RETURN to exit the current menu.

! Press HOME MENU at any time to exit the HOME MENU.

2 Select ‘System Setup’ from the HOME MENU, then press ENTER.

3 Select ‘MHL Setup’ from the System Setup menu.

4 Select the ‘Auto input switching’ from the MHL Setup menu.

5 Use k/l to select the setting.

! OFF – Does not automaticly switch to MHL input.

! ON – Automatically switches to MHL input.

6 Select ‘OK’, then press ENTER.

Notes

! This is only valid for MHL-compatible devices supporting this function.

! When the power is on, the MHL-compatible device is charged. (This receiver supports charging of devices up

to 0.9 A.)

The Other Setup menu

The Other Setup menu is where you can make customized settings to reflect how you are using the receiver.

1 Press MAIN RECEIVER to switch the remote control to the receiver operation mode, and

then press HOME MENU.

A Graphical User Interface (GUI) screen appears on your TV. Use i/j/k/l and ENTER to navigate through the

screens and select menu items. Press RETURN to exit the current menu.

2 Select ‘System Setup’ from the HOME MENU.

3 Select ‘Other Setup’, then press ENTER.

4 Select the setting you want to adjust.

If you are doing this for the first time, you may want to adjust these settings in order:

! Auto Power Down – Sets the power to turn off automatically when the receiver is not being used (page 113 ).

! Volume Setup – Sets up the volume-related operations of this receiver (page 113 ).

! Software Update – Use to update the receiver’s software and check the version (page 113 ).

! On Screen Display Setup – Sets whether or not to display the status on the display when the receiver is oper-

ated (page 114 ).

! Remote Control Mode Setup – Sets this receiver’s remote control mode (page 114 ).

! ZONE Setup – Use to make the sub zone-related settings (page 114 ).

! Maintenance Mode – This is used to receive maintenance from a Pioneer service engineer or custom

installer (page 115 ).

5 Make the adjustments necessary for each setting, pressing RETURN to confirm after each

screen.

1 2 ... 107 108 109 110 111 112 113 114 115 116 117 ... 148 149

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX59 Manuel d'utilisateur Page 112

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer SC-LX59