Pioneer SC-LX59 Manuel d'utilisateur télécharger pdf (Page 114)

114

The System Setup and Other Setup menus

Software Update messages

Status messages Descriptions

FILE ERROR

Try disconnecting then reconnecting the USB device or storing the update file again. If the error still

occurs, try using a different USB memory device.

No update file was found on the USB memory device. Store the file in the USB memory device’s root

directory.

UPDATE ERROR 1 to

UPDATE ERROR 7

Turn the receiver’s power off, then turn it back on and try updating the software again.

Update via USB

If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a

USB memory device and connect the device to the USB port. When the file is found, software updating

starts automatically.

UE11

Updating has failed. Use the same procedure to update the software again.

UE22

UE33

The software update failed. This receiver’s setup screen may no longer appear on the TV screen. Using

the USB memory, perform the software update while looking at the receiver’s front panel display.

(Refer to the following.)

Using USB memory, update the software while looking at the front panel display on

this receiver

1 Press MAIN RECEIVER to switch the remote control to the receiver operation mode, and

then press HOME MENU.

2 Use i/j, to select ‘System Setup’ and press ENTER.

3 Use i/j, to select ‘Other Setup’ and press ENTER.

4 Use i/j, to select ‘Update’ and press ENTER.

5 Use i/j, to select ‘via USB’ and press ENTER.

6 Once “OK” appears, then press ENTER.

7 Once “UPDATE? cNO” appears, use k to select ‘YES’ and press ENTER.

Software update will start.

On Screen Display Setup

When the receiver is operated, its status (the input name, listening mode, etc.) is displayed superimposed over

the video output on the display. This status display can be turned off by switching this setting to OFF. The setting

can be made for the main zone and HDZONE, respectively.

! Default: ON (both the main zone and HDZONE)

1 Select ‘On Screen Display Setup’ from the Other Setup menu.

2 Select and set the main zone or HDZONE for which you wish to change the setting.

3 Select the On Screen Display setting you want.

4 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Notes

! The on-screen display is only displayed for video output from the HDMI terminal.

! When the video input signal is 3D signal or partially 4K, the OSD screen is not displayed.

! The size of the characters displayed differs according to the output resolution.

Remote Control Mode Setup

! Default setting: 1

This sets this receiver’s remote control mode to prevent erroneous operation when multiple units of the receiver

are being used.

1 Select ‘Remote Control Mode Setup’ from the Other Setup menu.

2 Select the Remote Control Mode setting you want.

3 Select ‘OK’ to change the remote control mode.

4 Follow the instructions on the screen to change the remote control’s setting.

See Operating multiple receivers on page 97 .

5 When you’re finished, press RETURN.

You will return to the Other Setup menu.

ZONE Setup

Switches the sub-zone setting.

MAIN/HDZONE setting (setting for how to use the HDMI OUT 3 terminal)

1 Select ‘ZONE Setup’ from the Other Setup menu.

2 Select ‘MAIN/HDZONE’, then press ENTER.

3 Set how the HDMI OUT 3 terminal is to be used.

! MAIN: Select this to output the same input source as in the main zone.

After setting this to MAIN, exit the home menu, then press OUT P. and select the terminal for HDMI output

(page 92 ).

! HDZONE (default): Use the HDMI output’s multizone function (HDZONE) to output an input source different

from the one in the main zone (page 93 ).

4 Select ‘OK’, then press ENTER.

ZONE 2/ZONE 3/HDZONE setting

The volume setting and tone for the sub zones that can be used with this receiver can be changed and adjusted

here.

! When making multi-zone connections using the AUDIO ZONE 2 OUT or AUDIO ZONE 3 OUT terminals and

performing playback in Zone 2 or Zone3, you can set whether to adjust the Zone 2 or Zone3 volume on the

receiver or to fix it to a specific volume (–40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment

from the factory, allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from

the connected amplifier, make the setting below.

! HDZONE can be set when Speaker System is 7.2ch + HDZONE, 5.2 Bi-Amp+HDZONE or

5.2 +ZONE 2+HDZONE.

! HDZONE is set to Variable. It cannot be set to –40 dB Fixed and 0 dB Fixed.

CAUTION

! Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals

is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may

be produced even when Volume Level is set to –40 dB Fixed.

1 Select ‘ZONE Setup’ from the Other Setup menu.

2 Select a sub zone for which you wish to change the setting.

1 2 ... 109 110 111 112 113 114 115 116 117 118 119 ... 148 149

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX59 Manuel d'utilisateur Page 114

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer SC-LX59