Pioneer SC-LX59 Manuel d'utilisateur télécharger pdf (Page 122)

122

FAQ

Remote control

Symptom Remedy

Cannot be remote controlled. Set the remote control unit’s remote control mode so that it matches the setting on the

main unit (see Operating multiple receivers on page 97 ).

Check whether the receiver’s remote control mode is properly set (see Remote Control

Mode Setup on page 114 ).

Try replacing the batteries in the remote control (see Loading the batteries on page 10 ).

Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel

(see Operating range of remote control unit on page 10 ).

Check that there are no obstacles between the receiver and the remote control.

Make sure that there is no fluorescent or other strong light shining on to the remote

sensor.

Other components can’t be operated

with the system remote.

If the battery ran down, the preset codes may have been cleared. Re-enter the preset

codes.

The preset code may be incorrect. Redo the procedure for entering preset codes.

When commands from the remote control units of other devices are registered using the

learning function, in some cases they may not be learned properly. In this case, register

the commands again using the learning function (see page 98 ). If they still do not work,

they may be in a special format that cannot be registered on this receiver’s remote con-

trol. Operate the device using another remote control.

HDMI

Symptom Remedy

The HDMI indicator blinks continu-

ously.

Check all the points below.

Video/audio is not output or is inter-

rupted.

This receiver is HDCP-compatible. Check that the components you are connecting are

also HDCP-compatible. If they are not, please connect them using the component or

composite video jacks.

Depending on the connected source component, it’s possible that it will not work with

this receiver (even if it is HDCP-compatible). In this case, connect using the component

or composite video jacks between source and receiver.

If the problem still persists when connecting your HDMI component directly to your

monitor, please consult the component or monitor manual or contact the manufacturer

for support.

If video images do not appear on your TV, try adjusting the resolution, Deep Color or other

setting for your component.

While analog video signals are being output over HDMI, use a separate connection for

audio output.

To output signals in Deep Color, use an HDMI cable (High Speed HDMI

Cable) to

connect this receiver to a component or TV with the Deep Color feature.

The picture and sound output get cut

off, or there is no output produced.

Influence from a TV whose power is set to standby may cause the picture or sound output

to not be produced or to get cut off. In this case, press OUT P., and make sure to use an

output other than the HDMI output to which that TV is connected.

No picture.

Try changing the SCAL setting (in Setting the Video options on page 89 ).

To use the HDMI OUT 3 terminal in the main zone, set the MAIN/HDZONE

Output Setting to MAIN (page 114 ).

Symptom Remedy

No sound, or sound suddenly

ceases.

Check that the HDMI Audio setting is set to AMP (Setting the Audio options on page 87 ).

If the component is a DVI device, use a separate connection for the audio.

If analog video is being output over HDMI, please use a separate connection for the

audio.

Check the audio output settings of the source component.

HDMI format digital audio transmissions require a longer time to be recognized. Due

to this, interruption in the audio may occur when switching between audio formats or

beginning playback.

Turning on/off the device connected to this unit’s HDMI OUT terminal during playback,

or disconnecting/connecting the HDMI cable during playback, may cause noise or inter-

rupted audio.

Noisy or distorted picture. Sometimes a video deck may output a noisy video signal (during scanning, for example),

or the video quality may just be poor (with some video game units, for example). The

picture quality may also depend on the settings, etc. of your display device. Switch off

the video converter and reconnect the source and display device using the same type of

connection (component or composite), then start playback again.

If the problem still persists when connecting your HDMI component directly to your

monitor, please consult the component or monitor manual or contact the manufacturer

for support.

Synchronized operation not possible

using Control with HDMI function.

Check the HDMI connections.

The cable may be damaged.

Select ON for the Control Mode with HDMI setting (see HDMI Setup on page 83 ).

Turn the TV’s power on before turning on this receiver’s power.

Set the TV side Control with HDMI setting to on (see TV’s operating instructions).

Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to OUT 1. Then

turn on first the TV’s power, then this receiver’s power.

When HDZONE is set to ON, the

video resolution and number of

audio channels for the main zone

side changes.

This is due to the HDMI connection specifications; it is not a malfunction. When play-

ing the same input in the main zone and HDZONE, video and audio signals that can be

output in common for all the devices connected to the HDMI OUT 1, HDMI OUT 2 and

HDMI OUT 3 (HDZONE) terminals are set.

HDZONE cannot be turned on.

Set Output Setting at MAIN/HDZONE to HDZONE (page 114 ).

When the input source for the main

or HDZONE is switched or when

the power of the respective zones is

turned on and off, the audio or video

of the HDMI output terminal that is

not being operated is sometimes

interrupted.

This is because the HDMI devices need to recognize each other again. This is not a

malfunction. If the picture is disturbed or not displayed, turn off the power of the devices

in all the zones, then try again. Also try temporarily turning the Network Standby and

Standby Through settings OFF.

Such menus as the HOME MENU as

well as the on-screen display are not

displayed for HDMI OUT 1 or HDMI

OUT 2.

Press OUT P. and switch the HDMI OUT 1/2 setting.

Cannot upscale to 4K.

Change V.CONV to ON. (page 89 )

Change SCAL. (page 89 )

When HDZONE is turned on, upscaling cannot be performed. To perform upscaling, turn

off HDZONE (page 93 ).

1 2 ... 117 118 119 120 121 122 123 124 125 126 127 ... 148 149

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX59 Manuel d'utilisateur Page 122

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer SC-LX59