Pioneer SC-LX85 Manuel d'utilisateur Page 63
- Page / 122
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
63
En
09
Using other functions
! The synchronized amp mode is canceled
when the HDMI output is switched. If you wish
to use the synchronized amp mode, switch to
HDMI OUT 1, then select the synchronized
amp mode on the TV using the TV’s remote
control.
About the Speaker B Link function
When 7.1ch + Speaker B or
5.1ch + SP-B Bi-Amp is selected for the
Speaker System setting (page 87) and the
Speaker B Link setting (HDMI Setup on page
54) is turned on, the setting of the played
speaker terminals switches automatically when
HDMI OUT is switched.
The settings switch as follows:
! HDMI OUT ALL – Switches to SP: A+B ON.
Sound is output simultaneously in the room
where the A speakers are located and in the
room where the B speakers are located.
! HDMI OUT 1 – Switches to SP: A ON. Sound
is only output in the room where the A
speakers are located.
! HDMI OUT 2 – Switches to SP: B ON. Sound
is only output in the room where the B
speakers are located.
Checking your system settings
Use the status display screen to check your
current settings for features such as surround
back channel processing and your current
MCACC preset.
1 Set the remote control to the receiver
operation mode, then press STATUS to
check the system settings.
The front panel display shows each of the fol-
lowing settings for three seconds each: Input
Source d Sampling Frequency d MCACC
preset d ZONE 2 input d ZONE 3 input d
HDMI OUT.
2 When you’re finished, press STATUS
again to switch off the display.
Resetting the system
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this. Set MULTI-ZONE to
MULTI ZONE OFF.
! Disconnect the iPod and USB memory device
from the receiver beforehand.
! Set the Control with HDMI to OFF (see HDMI
Setup on page 54).
1 Switch the receiver into standby.
2 While holding down ENTER on the
front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET k/l,
then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.
! Note that all settings will be saved, even if the
receiver is unplugged.
Default system settings
Setting Default
Digital Video Converter ON
SPEAKERS FH/FW
Speaker System 9.1ch FH/FW
Speaker Setting
Front SMALL
Center SMALL
FH/FW SMALL
Surr SMALL
SB SMALLx2
SW YES
Surround Position IN REAR
Crossover 80 Hz
X-Curve OFF
DIMMER
Medium
bright
Inputs
See Input function default and possible settings on
page 36.
HDMI
HDMI Audio Amp
HDMI output
HDMI OUT
ALL
Control ON
Control Mode ALL
Display Power Off YES
Audio playback
Power On Level LAST
Volume Limit OFF
Mute Level FULL
Phase Control ON
Auto Sound
Retriever
iPod/USB,
HOME MEDIA
GALLERY,
ADAPTER PORT
input function
ON
Other input
functions
OFF
Setting Default
Sound Delay 0.0 frame
Dual Mono CH1
DRC AUTO
SACD Gain 0 dB
LFE Attenuate 0 dB
Auto delay OFF
Digital Safety OFF
Effect Level
ExtendedStereo 90
Other modes 50
2 PL II Music
Options
Center Width 3
Dimension 0
Panorama OFF
Neo:X Options Center Gain
Neo:X
CINEMA: 1.0
Neo:X
MUSIC: 0.3
Neo:X
GAME: 1.0
2 PL IIz Options
Height Gain MID
All Inputs
Listening Mode
(2 ch/multi ch)
AUTO
SURROUND
Listening Mode
(Headphones)
STEREO
See also Setting the Audio options on page 57 for
other default DSP settings.
MCACC
MCACC Position Memory
M1:
MEMORY 1
Channel Level (M1 to M6) 0.0 dB
Speaker Distance (M1 to M6) 3.00 m
Standing Wave
(M1 to M6)
ATT of all chan-
nels/filters
0.0 dB
SWch Wide Trim 0.0 dB
EQ Data (M1
to M6)
All channels/
bands
0.0 dB
EQ Wide Trim 0.0 dB
- IMPORTANT 2
- Contents 3
- 12 The Advanced MCACC menu 4
- Setup menus 4
- Before you start 6
- 01 Before you start 8
- 02 Controls and displays 10
- Controls and displays 11
- Connecting your equipment 14
- 03 Connecting your equipment 16
- Indoor antenna 29
- (vinyl-coated wire) 29
- Connecting to the network 30
- Basic Setup 34
- 04 Basic Setup 36
- Basic playback 38
- 05 Basic playback 40
- Listening to your system 45
- 06 Listening to your system 46
- Playback with HOME MEDIA 49
- GALLERY inputs 49
- Playback with Home Media 50
- Advanced operations for 51
- Internet radio 51
- About network playback 51
- About playable file formats 53
- Control with HDMI function 54
- 08 Control with HDMI function 56
- Using other functions 57
- 09 Using other functions 58
- (In case of SC-LX85) 64
- Programming signals from 65
- Multi Operation and System 67
- Controlling components 68
- TV and Audio/Video components 69
- Audio/Video components 69
- TV (Projector) 70
- Operating other components 71
- Precautions regarding 72
- Usable range 73
- Signal reflection 73
- (In case of SC-LX75) 74
- This receiver’s 75
- Other remote 75
- Direct function 76
- Setting the backlight mode 76
- Resetting the remote control 77
- The Advanced MCACC menu 80
- About remote control 87
- Manual speaker setup 87
- Speaker Setting 88
- Network Setup menu 89
- Network Standby 90
- Friendly Name 90
- Parental Lock 90
- Port Number Setting 90
- Checking the Network 91
- Information 91
- The Other Setup menu 91
- Software Update 93
- No sound 95
- 14 Additional information 100
- Troubleshooting 2 100
- AVNavigator 100
- Symptom Causes Remedy 100
- Symptom Remedy 100
- Additional information 101
- Symptoms Causes Remedies 102
- Satellite Set Top Box 119
- <ARB7462-A> 122
- © 2011 PIONEER CORPORATION 122
- All rights reserved 122
Produits connexes et manuels pour Systèmes de cinéma à domicile Pioneer SC-LX85
(78 pages)
(156 pages)© 2020, manymanuals.fr. Tous droits réservés | 3.688 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels