Pioneer DVD Menu Maker Instructions d'exploitation télécharger pdf (Page 53)

ADDITIONAL INFORMATION

Troubleshooting

Incorrect operations are often mistaken for trouble and

malfunctions. If you think that there is something wrong

with this component, check the points below.

Sometimes the trouble may lie in another component.

Inspect the other components and electrical appliances

being used. If the trouble cannot be rectified even after

exercising the checks listed below, ask your nearest

PIONEER authorized service center or your dealer to

carry out repair work.

The disc table comes back out automatically, shortly

after the disc table is closed.

The disc is dirty or warped.

\ Refer to

“Disc Care”

(page 50).

The disc is not placed properly on the disc table.

\ Use the disc table guide to align the disc (page 20).

Region number does not conform with this unit.

\ If the region number on the disc does not match

the number on the player, the disc cannot be used

(page 56).

There is condensation on the operating section of the

player.

\ Allow time for condensation to evaporate. If player

is near an air conditioning unit, you should move

the player (page 51).

Playback is not possible.

The disc has been loaded upside down.

\ Check that the disc has been loaded with the label

side facing up.

mark appears on screen.

The selected function does not operate for that disc.

mark appears on screen.

The operation is prohibited by the player.

Picture playback stops and the operation buttons

cannot be used.

Player malfunctions.

\ Stop disc playback (press STOP 7), then start

playback again.

New settings made in the Setup screen menus while

a disc is playing are ineffective.

Some settings can be changed while a disc is playing,

but are not effective. This is not a malfunction.

\ Make the same setting when the player is

stopped.

\ Stop disc playback (press STOP 7), then start

playback again. When playback is resumed, the

new settings should be in effect. Please note that

making settings in the Setup screen menus may

cancel the resume function.

When making changes in the Setup screen menus,

is displayed.

There is a Video CD or CD loaded in the player and the

setting that was changed only applies to DVD

performance.

\ The setting will be effective the next time a DVD

is loaded.

Settings are canceled.

When the power is turned off by power failure or by

unplugging the power cord, settings will be canceled.

\ Before unplugging the power cord, press

STANDBY/ON and check that “--OFF--”

disappears in the display.

No picture.

The rear panel’s VIDEO OUT SELECT switch setting

is not correct.

\ Check that the VIDEO OUT SELECT switch is set

to the correct position for the monitor connection

you are using (page 16).

Connection is incorrect.

\ Check that cord connections are correct and that

plugs are firmly connected.

Operation (settings) of TV or AV amplifier is not

appropriate.

\ Be sure that your TV, receiver, or amplifier is set

up to view DVD playback.

The [Component Video] menu is set to

[Progressive] but your TV/monitor is not compatible

with progressive scan.

\ Reconnect the player to your TV using a

composite or S-video cord, then set the VIDEO

OUT SELECT switch on the rear panel to

COMPOSITE & S-VIDEO. With your TV

connected using either the composite or S-Video

terminals, choose the [Interlace] setting in the

[Component Video] menu, then set the rear

panel switch back to COMPONENT (page 29).

\ Reset the player (page 49). [Component Video]

will be reset to [Interlace] but you’ll also loose

other settings.

The screen is stretched or aspect does not change.

The multi aspect setting is not appropriate.

\ Change the aspect setting in the [TV Screen]

setting in the Setup screen Video menu to the

screen type most appropriate to the TV or monitor

you are using (page 28).

This is not a malfunction.

\ The aspect ratio of some progressive-scan

compatible TVs cannot be changed.

Picture disturbance during playback or dark.

(Interlace/Progressive-scan)

This is not a malfunction.

\ This player is compatible with Macro-Vision

System copy guard. Some discs include a copy

prevention signal, and when this type of disc is

played back, stripes etc., may appear on some

sections of the picture depending on the TV.

When using progressive-scan.

\ If your TV is connected using the COMPONENT

VIDEO OUT jacks, set the [Component Video]

menu to [Interlace] (page 29).

When recorded on a VCR or passed through an AV

selector, there is disturbance in the playback picture.

This is not a malfunction.

\ Due to the player’s copy protection circuits,

connection of this device through a VCR or an AV

selector may prevent recording or cause picture

problems.

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 59 60

Commentaires sur ces manuels

Pas de commentaire

Pioneer DVD Menu Maker Instructions d'exploitation Page 53

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de CD Pioneer DVD Menu Maker