Pioneer AVIC D3 Manuel d'opérations télécharger pdf (Page 107)

105

Chapter 8 Customising the Audio Source SettingAV

Adjusting a position effect

You can select a listener position that you want to

make as the centre of sound effects.

1 Touch “Staging” in the Sound menu.

2 Touch “Position”.

3 Touch the desired position.

Adjusting loudness

Loudness compensates for deficiencies in the

low- and high-sound ranges at low volume.

1 Touch “Loudness” in the Sound menu.

2 Touch “On” to turn loudness on.

To turn loudness off, touch “Off”.

3 Touch 4 or 6 to select a desired level.

Each time you touch 4 or 6 selects level in

the following order:

Low – Mid – High

Using subwoofer output

This navigation system is equipped with a sub-

woofer output which can be turned on or off.

❒ When the subwoofer output is on, you can

adjust the cut-off frequency, the output level

and the phase of the subwoofer.

1 Touch “Sub Woofer” in the Sound menu.

When Preout (the subwoofer controller set-

ting in Initial menu) is Full, you cannot select

“Sub Woofer”.

➲ “Setting the rear output and subwoofer

controller” ➞ Page 109

2 Touch “On” to turn subwoofer output on.

To turn subwoofer output off, touch “Off”.

3 Touch “Reverse” or “Normal” to select

the phase of subwoofer output.

4 Touch “+” or “–” to adjust the output

level of the subwoofer.

+6 to –6 is displayed as the level is increased

or decreased.

5 Touch 4 or 6 to select cut-off frequency.

Each time you touch 4 or 6 selects cut-off

frequencies in the following order:

50 – 80 – 125 (Hz)

Only frequencies lower than those in the

selected range are output from the subwoofer.

Using non fading output

When the non fading output setting is on, the

audio signal does not pass through navigation

system’s low pass filter (for the subwoofer), but is

output through the RCA output.

1 Touch “Non Fading” in the Sound menu.

Only when Preout (the subwoofer controller

setting in Initial menu) is Full, you can select

“Non Fading”.

➲ “Setting the rear output and subwoofer

controller” ➞ Page 109

2 Touch “On” to turn non fading output on.

To turn non fading output off, touch “Off”.

3 Touch “+” or “–” to adjust the output

level of the non fading.

+6 to –6 is displayed as the level is increased

or decreased.

Using the high pass filter

When you do not want low sounds from the sub-

woofer output frequency range to play from the

front or rear speakers, turn the HPF (high pass

filter) on. Only frequencies higher than those in

the selected range are output from the front or

rear speakers.

1 Touch “HPF” in the Sound menu.

2 Touch “On” to turn high pass filter on.

To turn high pass filter off, touch “Off”.

3 Touch 4 or 6 to select cut-off frequency.

Each time you touch 4 or 6 selects cut-off

frequencies in the following order:

50 – 80 – 125 (Hz)

When Preout (the subwoofer controller set-

ting in Initial menu) is Sub. W, the HPF

function is effective for front speakers only.

Audio Adjustments

MAN-AVIC-D3-EN.book Page 105 Monday, January 15, 2007 8:51 AM

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 157 158

Commentaires sur ces manuels

Pas de commentaire

Pioneer AVIC D3 Manuel d'opérations Page 107

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs de médias en voiture Pioneer AVIC D3