Pioneer VSX-47TX Manuel d'utilisateur Page 36

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 112
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 35
36
1
2.Surround Setup
[ Check ]
[ 1.Speaker Systems ]
[ 2.Channel Delay ]
[ 3.Channel Level ]
[ 4.Acoustic Cal ]
[Return]
Setting Up for Surround Sound
1
SPEAKER SYSTEMS should be
selected. If it isn’t use the 5∞ buttons
to select it. Press the ENTER button.
The setup possibilities appear on your TV.
2
Use the 5∞ buttons to select the
speaker system setting.
Choose from :
MANUAL FREE : Sets all the speakers
MANUAL THX : Sets all the speakers to SMALL. The
crossover frequency is fixed at 80kHz. You can only select
the number of surround back speakers.
DIRECT ACCESS DISP MODE
+
+
10 DISC
ENTER
TONE
9
BASS/TREBLE
0
SYSTEM SETUP
TUNER EDIT
MENU
REMOTE SETUP
STATUS
MPX
GUIDE
EXIT
RETURN
ENTER
TUNING
1
DTV ON/OFF
TUNING
+
¡
8
3
EXTRA MENU
BAND
1~10
SPEAKER SYSTEMS
The following steps show you how to select the correct setup for the type and number of speakers you
connected. Most importantly, you need to decide how to route the sound for all the speakers you connected. To
do this select the size of the front, center, surround and surround back speakers (if you hooked them up). It is
important to make these settings as accurately as possible or, in some cases, you may not get the full
soundtrack from a disc. The auto setup from the microphone in the remote control may not properly assess the
size of your speakers if there is background noise, from an air conditioner or refrigerator, for example. If
necessary try different possible settings manually.
Use the information below to complete the steps that follow and set up the receiver to match the speakers you
have hooked up. Make sure the microphone is hooked up to the front panel and in the appropriate position
before starting. See page 13 for more information on setting up the microphone.
FRONT (default setting is SMALL)
Select SMALL to send bass frequencies to the subwoofer. Select LARGE if your speakers will reproduce bass
frequencies effectively or if you did not connect a subwoofer. (If you select SMALL for the front speakers the
subwoofer will automatically be switched YES. Also, the center and surround speakers cannot be set to
LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer .)
CENTER (default setting is SMALL)
Select LARGE if your speaker will reproduce bass frequencies effectively .
Select SMALL to send bass frequencies to the other speakers or subwoofer.
If you did not connect a center speaker, choose NO. In this case, the center channel is output from the
front speakers.
SURROUND (default setting is SMALL)
Select LARGE if your speakers will reproduce bass frequencies effectively .
Select SMALL to send bass frequencies to the other speakers or subwoofer.
If you did not connect surround speakers choose NO. In this case, the sound of the surround channels is
output from the front and center speakers.
Remember, If you select SMALL for the front speakers, the surround and surround back speakers can only
be set to SMALL.
SURROUND BACK (default setting is SMALL X2)
Select the number of surround back speakers you have. You can choose one speaker, two, or none.
If you select one, make sure that speaker if hooked up to the left surround back terminal.
Select LARGE if your speakers will reproduce bass frequencies effectively .
Select SMALL to send bass frequencies to the other speakers or subwoofer.
If you did not connect surround back speakers choose NO.
If the front speakers or the surround speakers are set to SMALL, the surround back speakers will automati-
cally be set to SMALL.
If you choose THX in step 2 then the surround back speakers can only be set to SMALL (X1 or )2, or NO.
SUBWOOFER (default setting is YES)
Leave it selected if you connected a subwoofer.
If you selected SMALL for the front speakers the subwoofer will automatically be set to on (you won’ t be
able to choose NO or PLUS).
If you did not connect a subwoofer choose NO. In this case, the bass frequencies are output from the front
or surround speakers.
• Choose the PLUS setting if you want stronger reproduction of deep bass sounds.
If you select PLUS the bass frequencies that would normally come out the front and center speakers are all
routed to the subwoofer.
Vue de la page 35
1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 111 112

Commentaires sur ces manuels

Pas de commentaire