Pioneer VSX-322-K Manuel d'utilisateur télécharger pdf (Page 28)

Additional information

Chapter 7:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and

malfunctions. If you think that there is something wrong with

this component, check the points below. Take a look at the

other components and electrical appliances being used,

because sometimes the problem may lie there. If the trouble

isn’t sorted out even after going through the checks below,

ask your nearest Pioneer authorized independent service

company to carry out repair work.

• If the unit does not operate normally due to external

effects such as static electricity disconnect the power

plug from the outlet and insert again to return to normal

operating conditions.

General

The power does not turn on.

 Disconnect the power plug from the outlet, and insert again.

 Make sure there are no loose strands of speaker wire touching

the rear panel. This could cause the receiver to shut off

automatically.

The receiver suddenly switches off.

 When the Auto Power Down function is working, the power

will automatically turn off if the receiver has not operated for

several hours. Check the setting for the Auto Power Down

function (see The Auto Power Down menu on page 26).

 After about a minute (you won’t be able to switch the unit on

during this time), switch the receiver back on. If the message

persists, call a Pioneer authorized independent service

company.

Power automatically turns ON/OFF and the input switches

from one to another. (When the ARC function is ON)

 The CEC (Consumer Electronic Control) function may activate

when the ARC function is turned ON, causing power to turn

ON and OFF and the input to switch from one to another.

Since this unit does not guarantee synchronized operation

based on the CEC function, turn OFF the HDMI CONTROL

setting on the connected player. Refer to the relevant device’s

instruction manual for details.

If this does not work, turn OFF the ARC function. If this is the

case, listen to the TV audio after connecting this unit and the

TV with an audio cable.

No sound is output when an input function is selected.

 Use MASTER VOLUME to turn up the volume.

 Press MUTE on the remote control to turn muting off.

 Set the SIGNAL SEL to H (HDMI), C1/O1 (digital) or A (analog)

according to the type of connections made (refer to page 17).

 Make sure the component is connected correctly (refer to

Connecting your equipment on page 10).

 Check the audio output settings of the source component.

 Refer to the instruction manual supplied with the source

component.

No image is output when an input function is selected.

 Make sure the component is connected correctly (refer to

Connecting your equipment on page 10).

 Use the same type of video cables for the source component

and TV to connect to this receiver (see About video outputs

connection on page 13).

 The video input selected on the TV monitor is incorrect. Refer

to the instruction manual supplied with the TV.

No sound from subwoofer.

 Make sure the subwoofer is switched on.

 The Dolby Digital or DTS source you are listening to may not

have an LFE channel.

 Switch the subwoofer setting in Speaker Setting on page 25 to

YES or PLUS.

 Switch the LFE ATT (LFE Attenuate) on page 24 to LFEATT 0 or

LFEATT 5.

No sound from surround or center speakers.

 Connect the speakers properly (refer to page 11).

 Refer to Speaker Setting on page 25 to check the speaker

settings.

 Refer to Channel Level on page 26 to check the speaker levels.

The Phase Control feature doesn’t seem to have an audible

effect.

 If applicable, check that the lowpass filter switch on your

subwoofer is off, or the lowpass cutoff is set to the highest

frequency setting. If there is a PHASE setting on your

subwoofer, set it to 0º (or depending on the subwoofer, the

setting where you think it has the best overall effect on the

sound).

 Make sure the speaker distance setting is correct for all

speakers (see Speaker Distance on page 26).

Considerable noise in radio broadcasts.

 Connect the antenna (page 15) and adjust the position for

best reception.

 Route any loose cables away from the antenna terminals and

wires.

 Fully extend the FM wire antenna, position for best reception,

and secure to a wall (or connect an outdoor FM antenna).

 Connect an additional internal or external AM antenna

(page 16).

 Turn off equipment causing interference or move it away from

the receiver (or move antennas farther away from equipment

causing noise).

Broadcast stations cannot be selected automatically.

 Connect an outdoor antenna (refer to page 16).

Noise during playback of a cassette deck.

 Move the cassette deck away from your receiver, until the

noise disappears.

No sound is output or a noise is output when software with

DTS is played back.

 Make sure the player’s settings are correct and/or the DTS

signal out is on. Refer to the instruction manual supplied with

the DVD player.

Can’t operate the remote control.

 Replace the batteries (refer to page 9).

 Operate within 7 m, 30º of the remote sensor (refer to page 9).

 Remove the obstacle or operate from another position.

 Avoid exposing the remote sensor on the front panel to direct

light.

The display is dark or off.

 Press DIMMER on the remote control repeatedly to return to

the default.

The front panel display switches over for no apparent

reason to various different displays.

 This happens because the demo display is in operation. To

turn off the demo display, press any button to go back to the

original display, or set the FL DEMO to OFF (see The FL Demo

Mode menu on page 26).

TEMP shows in the display and the volume level drops.

 The temperature within the unit has exceeded the allowable

value. Try moving the unit for better ventilation (see page 2).

 Lower the volume level.

1 2 ... 23 24 25 26 27 28 29 30 31

Commentaires sur ces manuels

Pas de commentaire

Pioneer VSX-322-K Manuel d'utilisateur Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer VSX-322-K