Pioneer SC-1525-K Manuel d'utilisateur télécharger pdf (Page 40)

Basic Setup

• If you see an ERR message (or the speaker

configuration displayed isn’t correct), there may be a

problem with the speaker connection.

If selecting RETRY doesn’t work, tur n off the power

and check the speaker connections. If there doesn’t

seem to be a problem, you can simply use / to

select the speaker and / to change the setting

and continue.

•If Reverse Phase is displayed, the speaker’s wiring

(+ and –) may be inverted. Check the speaker

connections.

– If the connections were wrong, turn off the power,

disconnect the power cord, then reconnect properly.

After this, perform the Full Auto MCACC procedure

again.

– If the connections were right, select GO NEXT and

continue.

7 Make sure ‘

’ is selected, then press

ENTER

A progress report is displayed on-screen while the

receiver outputs more test tones to determine the

optimum receiver settings.

Again, try to be as quiet as possible while this is

happening. It may take 3 to 10 minutes.

8 The Full Auto MCACC Setup procedure is completed

and the

Home Menu

menu reappears automatically.

Be sure to disconnect the microphone from this receiver

upon completion of the Full Auto MCACC Setup.

The settings made in the Full Auto MCACC Setup should

give you excellent surround sound from your system, but

it is also possible to adjust these settings manually using

The Advanced MCACC menu on page 75 or The System

Setup and Other Setup menus on page 84.

Problems when using the Auto MCACC Setup

If the room environment is not optimal for the Auto

MCACC Setup (too much background noise, echo off the

walls, obstacles blocking the speakers from the

microphone) the final settings may be incorrect. Check

for household appliances (air conditioner, fridge, fan,

etc.), that may be affecting the environment and switch

them off if necessary. If there are any instructions

showing in the front panel display, please follow them.

• Some older TVs may interfere with the operation of

the microphone. If this seems to be happening,

switch off the TV when doing the Auto MCACC Setup.

The Input Setup menu

You only need to make settings in the Input Setup menu

if you didn’t hook up your digital equipment according to

the default settings (see Input function default and

possible settings on page 41). In this case, you need to

tell the receiver what equipment is hooked up to which

terminal so the buttons on the remote control

correspond to the components you’ve connected.

1 Press on the remote control, then press

HOME MENU

A Graphical User Interface (GUI) screen appears on your

TV.

Use /// and ENTER to navigate through the

screens and select menu items. Press RETURN to

confirm and exit the current menu.

2 Select ‘

System Setup

’ from the

Home Menu

3 Select ‘

Input Setup

’ from the

System Setup

menu.

4 Select the input function that you want to set up.

The default names correspond with the names next to the

terminals on the rear panel (such as DVD or VIDEO)

which, in turn, correspond with the names on the remote

control.

5 Select the input(s) to which you’ve connected your

component.

For example, if your DVD player only has an optical

output, you will need to change the DVD input function’s

Digital In setting from COAX-1 (default) to the optical

input you’ve connected it to. The numbering (OPT-1 to 3)

corresponds with the numbers beside the inputs on the

back of the receiver.

Note

1If the speaker is not pointed to the microphone (listening position) or when using speakers that affect the phase (dipole speakers, reflective

speakers, etc.), Reverse Phase may be displayed even if the speakers are properly connected.

2• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12 cm (5 inches) will end up with

different size settings. You can correct the setting manually using the Manual speaker setup on page 84.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be accurate (taking

delay and room characteristics into account) and generally does not need to be changed.

• If Full Auto MCACC Setup mea

suremen

t results are incorrect due to the interaction of the speakers and viewing environment, we

recommend adjusting the settings manually.

RECEIVER

A/V RECEIVER

Exit Return

a.Manual SP Setup

b. Input Setup

c. OSD Language

d. Network Setup

e. Other Setup

4.System Setup 4b.Input Setup

A/V RECEIVER

Exit Finish

Input : DVD

Input Name : Rename

Digital In : COAX-1

HDMI Input :

---

Input Skip : OFF

Component In : Comp-1

12V Trigger1 : OFF

12V Trigger2 : OFF

SC-1525_UXJCB.book 40 ページ２０１０年４月２０日　火曜日　午後７時３２分

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 115 116

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-1525-K Manuel d'utilisateur Page 40

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer SC-1525-K