Pioneer Video Card PDA-5002 Manuel d'utilisateur Page 26
- Page / 33
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
26
En
Other Operations
English
3 OFF 3 HQ3 STANDARD
Other Operations
Setting the Regional TV System
Format
INPUT3 and INPUT4 are compatible with a number of TV
system formats used around the world, which are
automatically detected by this unit.
Normally “COLOR SYSTEM:AUTO” should be selected
for automatic detection. However, some video signals are
dubbed over or in certain conditions may not be displayed
properly (loss of color, etc.) by this setting. In this case,
change the setting according to the input signal.
Note
Setting the TV system format is required for both INPUT3 and
INPUT4. Setting assignment and exclusive use according to the
TV system format of your input signal will enable prompt
processing of signals and reduction of time for input selection
and possible errors in detecting signals.
1 Press MENU to display the menu screen.
RSETE
SELECT ENTER EXIT
SET
MENU
PICTURE SET UP OPTION
:
0
:
0
:
0
:
0
CONT RAST
:
0
BR
CLOR
IGHT.
:
:
:
O
TNTI
SARPH
MAIN MENU INPUT4
2 Press 2/3 to select SET UP.
SELECT ENTER EXIT
SET
MENU
PICTURE SET UP OPTION
:
A
UTO
:
M
OT I ON
COLOR
3D Y C/MDEO
OF FAUT O P OWER
SYSTEM
:
O
FF
:
M
IDDLECOLOR T MPE
:
L
OWDIGITAL NR
:
O
FFPURECI N MAE
INPUT LEBLA
HIGH CO TNRATS
:
O
FF
MAIN MENU INPUT4
:
INPUT
4
3 Press 5/∞ to select COLOR SYSTEM.
SELECT CHANGE EXIT
SET
MENU
PICTURE SET UP OPTION
:
M
OT I
M
ODE ON3D Y C/
OF FAUT O P OWER
:
O
FF
:
M
IDDLECOLOR T MPE
:
L
OWDIGITAL NR
:
O
FFPURE ICNMAE
INPUT LEBLA
HIGH CO TNRATS
:
O
FF
:
A
UTOCOL OR SYSTEM
MAIN MENU INPUT4
:
INPUT
4
Setting the PureCinema mode
When the PureCinema mode is selected, it functions
automatically to detect video signals of movies recorded at 24
frames-per-second, changing the scan settings to allow
enjoyment of higher quality movie playback. It does this by
converting the video signal to progressive scan. When using
the PureCinema function, it should odinarily be set to “HQ.”
Note, however, that due to the time required for video signal
processing, a time lag may occur with the audio signal, and if
this lag is objectionable, set the mode to “STANDARD.”
When set to OFF (factory default), only standard progressive
conversion is used.
Note
The PureCinema mode is supported only with 525i (480i) or
NTSC input signals.
This setting must be made independently for each input (INPUT
1 - INPUT 4) used.
1 Press MENU to display the menu screen.
PICTURE SET UP OPTION
:
0
:
0
:
0
:
0
CONT RAST
:
0
BR
CLOR
IGHT.
:
:
:
O
TNTI
SARPH
MAIN MENU INPUT1
2 Press 2/3 to select SET UP.
SELECT ENTER EXIT
SET
MENU
PICTURE SET UP OPTION
:
V
IDEO
:
R
GB
:
A
UTO
SETT I N
VIDEO SIGNAL
CLAM
OF FAUT O
P
POWER
:
G
:
O
FF
PSITIONO
:
M
IDDLECOLOR T MPE
:
L
OWDIGITAL NR
:
O
FFPUREC I N MAE
INPUT LEBLA
HIGH CO TNRATS
:
O
FF
MAIN MENU INPUT1
INPUT
1
3 Press 5/∞ to select PURECINEMA.
SELECT CHANGE EXIT
SET
MENU
PICTURE SET UP OPTION
INPUT LEBLA
:
V
IDEO
:
A
UTO
SETT I N
CLAM
OF FAUT O
P
POWER
G
:
O
FF
PSITIONO
:
L
OWDIGITAL NR
HIGH CO TNRATS
:
O
FF
:
R
GBVIDEO SIGNAL
:
O
FFPUREC I N MAE
:
M
IDDLECOLOR T MPE
MAIN MENU INPUT1
:
INPUT
1
4 Press SET to select the desired PureCinema mode.
Each time SET is pressed, the screen mode setting
changes as shown:
5 Following completion of the setting, press MENU
once again to return to the normal display.
- PDA-5002 1
- Before Proceeding 2
- Contents 2
- Checking Supplied Accessories 3
- Part Names and Functions 4
- Installation and Connections 6
- Display with Video Card 7
- Connection to AV components 8
- Connection to a personal 9
- Connection to INPUT3 10
- Connection to INPUT4 10
- DIGITAL RGB 11
- Audio Connections 12
- To remove speed clamps 13
- Setting Up the System 14
- CLAMP POSITION setup 15
- Operations 16
- During video signal input 18
- Partial Image Enlargement 19
- (POINT ZOOM) 19
- Automatic Power OFF 20
- Display Panel Adjustments 21
- Clock (Automatic Adjustment) 22
- Manual Adjustment of Screen 22
- Position and Clock 22
- Other Operations 24
- (COLOR TEMP) 25
- Setting the PureCinema mode 26
- Viewing a Fast Moving Picture 27
- (3D Y/C MODE) 27
- Viewing in a Bright Location 28
- (HIGH CONTRAST) 28
- AUTO FUNCTION 29
- Audio Output (AUDIO OUT) 30
- Input/output 31
- Accessories 31
- Supplement 1 32
- Supplement 2 32
- Explanation of Terms 33
Produits connexes et manuels pour Matériel Pioneer Video Card PDA-5002
Matériel Pioneer CD-BTB100 Manuel d'utilisateur
(137 pages)
(137 pages)
Matériel Pioneer CD-BTB200 Manuel d'utilisateur
(134 pages)
(134 pages)
Matériel Pioneer CD-BTB100 Manuel d'utilisateur
(175 pages)
(175 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.531 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels