Pioneer VSX-516-S/-K Manuel d'utilisateur télécharger pdf (Page 10)

Quick surround sound setup03

If you see an

ERR

message in the display, there

may be a problem with your mic or the speaker

connections. Turn off the power, and check the

problem indicated by the

ERR

message (see

below), then try the auto surround setup again.

•

ERR MIC

– Check microphone connection.

•

ERR Fch

– Check front speaker connections.

•

ERR Sch

– Check surround speaker

connections.

•

ERR SBch

– Check surround back speaker

connection.

•

ERR SW

– Make sure the subwoofer has

been switched on and volume on the

subwoofer is turned up.

6 When you see CHECK OK in the display,

confirm your speaker configuration.

Use

/

(cursor up/down) to check each

speaker in turn.

YES

should reflect the

actual speakers connected. If the speaker

configuration displayed isn’t correct, use

/



(cursor left/right) to change the setting.

When you’re finished, go to the next step.

7 Select CHECK OK in the display then press

ENTER

The Auto MCACC checks the subwoofer level.

• If the subwoofer output level is too high/

low,

SW.VOL.DWN

SW.VOL.UP

blinks in

the display for five seconds. To exit and

check your subwoofer output level, press

SETUP

or simply press

ENTER

when you’re

prompted to

RETRY?

The receiver outputs more test tones to

determine the optimum receiver settings for

speaker setting, channel level, speaker

distance, and Acoustic Calibration EQ.

8 The Auto MCACC Setup has finished!

The front panel MCACC indicator lights to

show the surround settings are complete.

The settings made in the Auto MCACC Setup

should give you excellent surround sound from

your system, but it is also possible to adjust

these settings manually using the System

Setup menu (starting on page 34).

Optionally, when you see

SKIP?

you can press

/

(cursor up/down) to select one of the

following options then press

ENTER

, and use

/

(cursor up/down) to check the settings:

•

CHK SP

– Check the size and number of

speakers you’ve connected (see page 38

for more on this)

•

CHK DIST.

– Check the distance of your

speakers from the listening position (see

page 39 for more on this)

•

CHK LEVEL

– Check the overall balance of

your speaker system (see page 39 for more

on this)

•

CHK EQ

– Select either

ALL CH

F ALIGN

to check the adjustments to the frequency

balance of your speaker system based on

the acoustic characteristics of your room

(see page 36 for more on this)

9 When you’re finished, select

‘SKIP?’

to go

back to the System Setup menu.

• Remember to disconnect the microphone

after completing the Auto MCACC Setup.

Other problems during Auto MCACC

If the room environment is not optimal for the

Auto MCACC Setup (too much background

noise, echo off the walls, obstacles blocking

the speakers from the microphone) the final

settings may be incorrect. Check for household

appliances (air conditioner, fridge, fan, etc.),

that may be affecting the environment and

switch them off if necessary.

If there are any

instructions showing in the front panel display,

please follow them.

Note

1• Depending on the characteristics of your room, sometimes identical speakers with cone sizes of around 12cm will end up

with different size settings. You can correct the setting manually using the

Speaker setting

on page 38.

• The subwoofer distance setting may be farther than the actual distance from the listening position. This setting should be

accurate (taking delay and room characteristics into account) and generally does not need to be changed.

2 Some older TVs may interfere with operation of the mic. You may want to switch off your TV during the Auto MCACC Setup.

VSX_516.book.fm 10 ページ２００６年２月２１日　火曜日　午後４時５２分

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 54 55

Commentaires sur ces manuels

Pas de commentaire

Pioneer VSX-516-S/-K Manuel d'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer VSX-516-S/-K