Pioneer PRV-LX1 Instructions d'exploitation télécharger pdf (Page 79)

PRV-LX1

Symptom

Main unit command buttons

don’t work.

Can’t output 96 kHz audio in

digital.

Remote control unit doesn’t

work.

Television malfunctions.

Memory settings are erased.

No sound from speakers, or

distorted sound.

When digital video camera is

connected to the unit’s DV

connectors, video images can’t

be viewed on television monitor.

Or no sound is audible.

DVD playback images can’t be

seen on the monitor screen of a

digital video camera connected

to the unit’s DV connectors. Or

no sound is audible.

Cause/Remedy

¶ Hold the STANDBY/ON button depressed for 4 seconds or more

to set unit to standby condition. If the STANDBY/ON button also

doesn’t work, turn off the main power switch on the rear panel.

¶ Some discs prohibit digital output of 96 kHz linear PCM audio. In

this case, even if the unit’s [96 kHz PCM OUT] command is set

to “96 kHz”, the signal will be converted to 48 kHz for output.

¶ Operate remote within proper range (7 m).

¶ Change to new batteries.

¶ Television monitors with wireless remote control functions may

malfunction when the PRV-LX1’s remote control unit is used. In

such cases, separate the television monitor and the PRV-LX1.

¶ If manual disconnection of the power cord or a power failure

occurs when the unit is turned on, previously input settings may

be erased. Disconnect the power cord only after pressing the

STANDBY/ON button so that the display’s POWER-OFF

indicator goes out.

¶ If television or AV amplifier’s sound volume is set to minimum,

raise the sound volume.

¶ When using audio input from external input connector, set the

[Audio Level] command.

¶ Check and confirm that all audio cables are connected properly.

¶ Check that all cable plugs are inserted securely in their

connectors or jacks.

¶ Clean any dirt from connection plugs and jacks.

¶ No sound is produced during still, frame advance, and slow playback.

¶ DTS audio is output only from unit’s digital audio output

connectors. To listen to DTS audio from a DVD disc, the unit’s

digital audio output connectors must be connected to the digital

audio input connectors of a DTS compliant amplifier, and the

[DTS OUT] command must be set to “ON”. If the connected

amplifier does not support DTS audio, use the remote control

unit’s AUDIO button or the disc menu to select an audio format

other than DTS.

¶ Check all connections. The PRV-LX1’s DV connectors allow the

connection of a single digital video camera. Connect the digital

video camera directly to the PRV-LX1.

¶ Check that the DV cable is connected properly.

¶ Try turning the power to the digital video camera OFF then ON again.

¶ Turn the power to the PRV-LX1 OFF then ON again.

¶ Check all connections. The PRV-LX1’s DV connectors allow the

connection of a single digital video camera. Connect the digital

video camera directly to the PRV-LX1.

¶ Check that the DV cable is connected properly.

¶ Try stopping playback and then starting it again.

¶ Try turning the power to the digital video camera OFF then ON again.

¶ Turn the power to the PRV-LX1 OFF then ON again.

¶ The video and audio of DVDs labeled “copying prohibited” or

“copy once only” cannot be output.

¶ The audio/video of a component connected to an external input

connector cannot be output.

¶ No video or audio signals are output during recording or during

recording pause.

¶ When using time shift playback (playback during recording), even

if recording alone is stopped, output of playback video/audio will

not begin. Stop playback temporarily, then start it once again to

begin signal output.

¶ Set [DV OUT] to “Enabled”.

Reference page

Malfunctions may be caused by static electricity or other external sources. In such cases, normal operation may be restored

by disconnecting the power cord and then reconnecting it again. If problem persist, consult your dealer.

TROUBLESHOOTING

1 2 ... 74 75 76 77 78 79 80 81 82 83 84 ... 88 89

Commentaires sur ces manuels

Pas de commentaire

Pioneer PRV-LX1 Instructions d'exploitation Page 79

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Pioneer PRV-LX1