Pioneer VSX-LX302 Manuel d'utilisateur télécharger pdf (Page 88)

> Network Functions > Specifications > Advanced Setup > Listening Modes

Troubleshooting Supplementary Information, etc�|

> Basic Manual

LINKS

Troubleshooting

Before starting the procedure

Problems may be solved by simply turning the power on/

off or disconnecting/connecting the power cord, which

is easier than working on the connection, setting and

operating procedure. Try the simple measures on both the

unit and the connected device. If the problem is that the

video or audio is not output or the HDMI linked operation

does not work, disconnecting/connecting the HDMI cable

may solve it. When reconnecting, be careful not to wind

the HDMI cable since if wound the HDMI cable may not

fit well. After reconnecting, turn off and on the unit and the

connected device.

•

This unit contains a microPC for signal processing

and control functions. In very rare situations, severe

interference, noise from an external source, or static

electricity may cause it to lockup. In the unlikely event

that this happens, unplug the power cord from the wall

outlet, wait at least 5 seconds, and then plug it back in.

•

Our company is not responsible for reparations for

damages (such as CD rental fees) due to unsuccessful

recordings caused by the unit's malfunction. Before you

record important data, make sure that the material will

be recorded correctly.

When the unit is operating erratically

■ Try restarting the unit

Restarting the unit may help it operate more smoothly.

To restart the unit, turn it to standby, and then press

STANDBY/ON on the main unit for at least 5 seconds.

(The unit's settings will be maintained.) If there is

no improvement even after the unit is restarted, try

disconnecting and reconnecting the power cords of the unit

and connected equipment.

■ Resetting the unit (this resets the unit settings to

the default)

If restarting the unit doesn't fix the problem, resetting the

unit to the status at the time of shipment may solve the

problem. If you reset the unit status, your preferences

will be reset to the defaults. Note them down before the

operation below.

1. While pressing the AUTO/DIRECT button on the main

unit, press

STANDBY/ON.

2. "Clear" appears on the display and the unit returns to

standby. Do not unplug the power cord until "Clear"

disappears from the display.

To reset the remote controller, while holding down MODE,

press

until the remote indicator flashes twice (3

seconds or more).

Power

■ Cannot turn on the unit

•

Make sure that the power cord is properly plugged into

the wall outlet.

•

Unplug the power cord from the wall outlet, wait 5

seconds or more, then plug it in again.

■ The unit turns off unexpectedly

•

The unit automatically switches to standby when the

"System Setup" - "Hardware" - "Power Management" -

"Auto Standby" setting in the Home screen functions.

•

The protective circuit function may have been activated.

If this has occurred, "AMP Diag Mode" appears on the

display when the unit is turned on again, and the unit

enters diagnostic mode. If the results of the diagnosis is

that there is no problem, the "AMP Diag Mode" display

disappears and you can use the unit normally again. If

"CHECK SP WIRE" appears on the display, the speaker

cables may be short-circuited. Make sure bare speaker

wires are not touching each other or the back panel of

the unit, then turn the unit on again. If "NG" is displayed,

immediately unplug the power cord from the wall outlet

and contact your dealer.

•

The protective circuit function may have been activated

because the temperature of the unit rose abnormally.

If this happens, then the power will continue to turn off

after you have turned the unit on again. Make sure the

unit has plenty of space for ventilation around it, wait for

the unit to cool down sufficiently, and then try turning it

on again.

WARNING: If smoke, smell or abnormal noise is produced

by the unit, unplug the power cord from the wall outlet

immediately and contact the dealer or our company's

support.

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 96 97

Commentaires sur ces manuels

Pas de commentaire

Pioneer VSX-LX302 Manuel d'utilisateur Page 88

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de Blu-Ray Pioneer VSX-LX302