Pioneer SC-LX58 Manuel d'utilisateur télécharger pdf (Page 109)

109

The System Setup and Other Setup menus

5 Select the Volume Limit setting you want.

The maximum volume for the zone selected in step 2 can be set.

! OFF (default) – The maximum volume is not limited.

! –20.0dB/–10.0dB – The maximum volume is limited to the value set here.

6 Select the Mute Level setting you want.

The mute level for the zone selected in step 2 can be set.

This sets how much the volume is to be turned down when MUTE is pressed.

! FULL (default) – No sound.

! –40.0dB/–20.0dB – The volume will be turned down to the level specified here.

7 Adjust Lch Level and Rch Level.

The channel level for the zone selected in step 2 can be set.

The level can be adjusted between –12.0dB and +12.0dB, in 1 dB steps.

8 Select the HPF (High Pass Filter) setting you want.

This can only be set when ZONE 2 is selected in step 2.

The low frequency component output from the AUDIO ZONE 2 OUT terminals is cut. When a subwoofer is con-

nected in Zone 2, we recommend setting this to “ON”. This is only valid when Zone 2 is connected using the

AUDIO ZONE 2 OUT terminals.

! OFF (default) – The High Pass Filter function is disabled.

! ON – The High Pass Filter function is enabled.

9 Select the TONE setting you want.

This can only be set when ZONE 2 is selected in step 2.

The bass and treble for ZONE 2 can be adjusted. When BYPASS is selected, the original sound is played as such.

When ON is selected, the BASS and TREBLE can be adjusted.

! When the speaker terminals are being used for ZONE 2, the ZONE 2 TONE effect is valid when

Speaker System is set to 5.2 Bi-Amp+HDZONE, 5.2 +ZONE 2+ZONE 3 or 5.2 +ZONE 2+HDZONE. When

set to 7.2ch + HDZONE, Multi-ZONE Music, the ZONE 2 TONE effect is not applied.

10 Adjust the bass (BASS) and treble (TREBLE) to your tastes.

This can only be set when ZONE 2 is selected in step 2 and ON is selected in step 8.

The BASS and TREBLE can each be adjusted between –10.0dB and +10.0dB, in 1 dB steps.

11 When you’re finished, press RETURN.

You will return to the Other Setup menu.

On Screen Display Setup

When the receiver is operated, its status (the input name, listening mode, etc.) is displayed superimposed over

the video output on the display. This status display can be turned off by switching this setting to OFF. The setting

can be made for the main zone and HDZONE, respectively.

! Default: ON (both the main zone and HDZONE)

1 Select ‘On Screen Display Setup’ from the Other Setup menu.

2 Select and set the main zone or HDZONE for which you wish to change the setting.

3 Select the On Screen Display setting you want.

4 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Notes

! The on-screen display is only displayed for video output from the HDMI terminal.

! When the video input signal is a 3D signal, the on-screen display may not be displayed.

! The size of the characters displayed differs according to the output resolution.

Play ZONE Setup

Select the zone for playing the audio contents of devices in the home network when using in the DMR mode.

! For playable DLNA-compatible network devices, see page 68 .

1 Select ‘Play ZONE Setup’ from the Other Setup menu.

2 Select the zone in which you want to play the audio contents.

3 When you’re finished, press RETURN.

You will return to the Other Setup menu.

Notes

! If another zone is on, it may not be possible to play the audio contents. In this case, turn the other zone off,

then play the audio contents.

! MAIN/HDZONE at ZONE Setup must be set to HDZONE in order to use the HDZONE function (page 108 ).

Maintenance Mode

Only use this if so instructed by a Pioneer service engineer or custom installer.

1 2 ... 104 105 106 107 108 109 110 111 112 113 114 ... 139 140

Commentaires sur ces manuels

Pas de commentaire

Pioneer SC-LX58 Manuel d'utilisateur Page 109

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer SC-LX58