Pioneer VSX-LX70 Manuel d'utilisateur Page 85
- Page / 99
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Additional information
14
85
En
Video
Settings
Symptom Remedy
No image is output when an input
is selected.
• Check the video connections of the source component (see page 16).
• For high-definition video (using component video connections), or when digital video conversion is
switched off (in Setting the Video options on page 71), you must connect your TV to this receiver using the
same type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component video, HDMI or
S-video cables (see The Input Setup menu on page 66).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If adjusting
this receiver’s Resolution setting (in Setting the Video options on page 71) and/or the resolution settings on
your component or display doesn’t work, try switching Digital Video Conversion (in Setting the Video options
on page 71) OFF.
Can’t record video. • Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video cable is
used for connecting both the recorder and the video source (the one you want to record) to this receiver.
Noisy, intermittent, or distorted
picture.
• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video
quality may just be poor (with some video game units, for example). The picture quality may also depend on
the settings, etc. of your display device. Switch off the video converter and reconnect the source and display
device using the same type of connection (component, S-video or composite), then start playback again.
Symptom Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also
Problems when using the Auto MCACC Setup on page 9). If the noise level cannot be kept low enough, you
will have to set up the surround sound manually (page 50).
After using the Auto MCACC
Setup, the speaker size setting is
incorrect.
• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch off
all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.
Change the speaker setting manually in Speaker Setting on page 50, and use the ALL (Keep SP SYSTEM)
option for the Custom Menu in Automatic MCACC (Expert) on page 39 if this is a recurring problem.
Can’t adjust the Fine Speaker
Distance setting (page 44)
properly.
• Check that the speakers are all in phase (make sure the positive (+) and negative (–) terminals are
matched up properly).
The display shows KEY LOCK
ON when you try to make
settings.
• With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS button to
disable the key lock.
Most recent settings have been
erased.
• The power cord was disconnected from the wall while adjusting this setting.
VSX_LX60LX70.book Page 85 Wednesday, June 6, 2007 3:13 PM
- Operating Instructions 1
- IMPORTANT 2
- Operating Environment 3
- Contents 4
- Before you start 6
- Control) 8
- Playing a source 9
- 5 minute guide 10
- Full Band Phase Control 10
- Connecting your equipment 12
- When making cable connections 13
- About the video converter 13
- DIGITAL OUT 15
- VIDEO S-VIDEOAUDIORL 15
- Connecting antennas 21
- Plugging in the receiver 22
- AC outlet 22
- Controls and displays 23
- Remote control 26
- Listening to your system 28
- Listening in stereo 30
- Using Stream Direct 30
- Selecting MCACC presets 31
- Choosing the input signal 31
- USB playback 34
- Using the tuner 36
- Chapter 7: 36
- Listening to the radio 36
- Saving station presets 36
- An introduction to RDS 37
- Using EON 38
- The System Setup menu 39
- Surround back speaker setting 42
- Manual MCACC setup 42
- Data Management 48
- Manual speaker setup 50
- Other connections 53
- Connecting using HDMI 54
- About HDMI 55
- Speaker B setup 56
- Front left 57
- Making MULTI-ZONE connections 58
- CONTROL ON/OFF 60
- MULTI – ZONE & 60
- SOURCE/REC SEL 60
- Pioneer plasma 61
- HDMI Control 64
- Setting the HDMI Control mode 65
- Other Settings 66
- The Other Setup menu 67
- Using other functions 70
- Setting the Video options 71
- 30 min 60 min 73
- Checking your system settings 74
- Resetting the system 74
- RECEIVER SOURCE 76
- TV CONTROL 76
- 3 cm to 5 cm 77
- Renaming input source names 78
- Direct function 78
- Controls for TVs 79
- Controls for other components 80
- ASSIGNABLE 81
- Additional information 82
- Surround sound formats 89
- About THX 90
- About Neural Surround 91
- Specifications 96
- Cleaning the unit 97
- Our philosophy 97
- PIONEER CORPORATION 99
Produits connexes et manuels pour Récepteurs et amplificateurs Pioneer VSX-LX70
(73 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.271 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels