Pioneer VSX-817-S/-K Manuel d'utilisateur télécharger pdf (Page 44)

The System Setup menu06

2 Use

/

to choose the speaker(s) that

you want to set then select a speaker size.

Use

/

to select the size (and number) of

each of the following speakers:

•

Front

(

) – Select

LARGE

if your front

speakers reproduce bass frequencies

effectively, or if you didn’t connect a

subwoofer. Select

SMALL

to send the bass

frequencies to the subwoofer.

•

Center

(

) – Select

LARGE

if your center

speaker reproduces bass frequencies

effectively, or select

SMALL

to send bass

frequencies to the other speakers or

subwoofer. If you didn’t connect a center

speaker, choose

(the center channel is

sent to the other speakers).

•

Surround

(

) – Select

LARGE

if your

surround speakers reproduce bass

frequencies effectively. Select

SMALL

send bass frequencies to the other

speakers or subwoofer. If you didn’t

connect surround speakers choose

(the sound of the surround channels is

sent to the other speakers).

•

Surround Back

(

)

(VSX-817 model only)

–

Select

LARGE

if your surround back

speaker reproduce bass frequencies

effectively. Select

SMALL

to send bass

frequencies to the other speakers or

subwoofer. If you didn’t connect surround

back speaker choose

•

Subwoofer

(

) – LFE signals and bass

frequencies of channels set to

SMALL

are

output from the subwoofer when

YES

selected.

Choose the

PLUS

setting if you

want the subwoofer to output bass sound

continuously or you want deeper bass (the

bass frequencies that would normally

come out the front and center speakers are

also routed to the subwoofer). If you did not

connect a subwoofer choose

(the bass

is output from other speakers).

Crossover network

• Default setting:

100Hz

This setting decides the cutoff between bass

sounds playing back from the speakers

selected as

LARGE

, or the subwoofer, and bass

sounds playing back from those selected as

SMALL

It also decides where the cutoff will

be for bass sounds in the LFE channel.

1 Select ‘

X.OVER’

from the SP SETUP menu.

2 Use

/

to choose the frequency cutoff

point.

Frequencies below the cutoff point will be sent

to the subwoofer (or

LARGE

speakers).

Channel level

Using these settings, you can adjust the overall

balance of your speaker system.

1 Select

CH LEVEL

from the SP SETUP menu.

2 Use

/

to select a setup option.

•

T. TONE M.

– Move the test tone manually

from speaker to speaker and adjust

individual channel levels.

•

T. TONE A.

– Adjust channel levels as the

test tone moves from speaker to speaker

automatically.

3 Confirm your selected setup option.

The test tones will start after you press ENTER.

Note

1 If you select SMALL for the front speakers the subwoofer is fixed to YES. Also, the center, surround, and surround back speak-

ers can’t be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer.

2• If the surround speakers are set to NO, the surround back speaker will automatically be set to NO.

• If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.

3 If you can’t get good bass results, listen to the bass response with the subwoofer set to PLUS and YES or the front speakers

set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option

is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.

4 For more on selecting the speaker sizes, see Speaker setting above.

5 After the volume increases to the reference level, test tones will be output.

VSX517_817.fm 44 ページ２００７年２月２２日　木曜日　午後８時１１分

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 62 63

Commentaires sur ces manuels

Pas de commentaire

Pioneer VSX-817-S/-K Manuel d'utilisateur Page 44

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs et amplificateurs Pioneer VSX-817-S/-K