Pioneer DV58AV_KU_EN Manuel d'utilisateur télécharger pdf (Page 24)

FAQ

• After I load a DVD disc, it ejects automatically after a few seconds!

Most likely, the disc is the wrong region for your player. The

region number should be printed on the disc; check it against

the region number of the player (which you can find on the rear

panel). See also DVD-Video regions on page 41.

If the region number is OK, it may be that the disc is damaged

or dirty. Clean the disc and look for signs of damage. See also

Taking care of your player and discs on page 40.

• Why won’t the disc I loaded play?

First check that you loaded the disc the right way up (label side

up), and that it’s clean and undamaged. See Taking care of your

player and discs on page 40 for information on cleaning discs.

If a disc loaded correctly won’t play, it’s probably an

incompatible format or disc type, such as DVD-ROM. See Disc/

content format playback compatibility on page 8 for more on disc

compatibility.

• There’s no picture!

Check the front panel and make sure that the PURE AUDIO

indicator isn’t lit. If it is, press the PURE AUDIO button to switch

the video and HDMI outputs back on. See also Front panel on

page 16.

Check that your TV is compatible with resolutions of 1080i, 720p,

or 480p. See Watching 1080i/720p/480p from the component

video outputs on page 12.

• I have a widescreen TV so why are there black bars at the top and

bottom of the screen when I play some discs?

Some movie formats are such that even when played on a

widescreen TV, black bars are necessary at the top and bottom

of the screen. This is not a malfunction.

• I have a standard (4:3) TV and set the player to show widescreen

DVDs in pan & scan format, so why do I still get black bars top and

bottom with some discs?

Some discs override the display preferences of the player, so

even if you have 4:3 (Pan & Scan) selected, those discs will still

be shown in letter box format. This is not a malfunction.

• I’ve connected to a HDMI compatible component but I can’t get

any signal and the front panel HDMI indicator won’t light!

Make sure that you’ve selected this player as the HDMI input in

the settings for the component you’re using. You may need to

refer to the instruction manual of the component to do this. See

Connecting using HDMI on page 14 for more on HDMI

compatibility.

• There’s no picture from the HDMI output!

This player cannot display pictures from DVI compatible

sources. See Connecting using HDMI on page 14 for more on

HDMI compatibility.

Make sure the resolution on this player matches that of the

component you have connected using HDMI. See Resolution

(Max) on page 33 to change the HDMI resolution.

• My AV receiver is definitely compatible with 96 kHz/88.2 kHz

Linear PCM audio, but it doesn’t seem to work with this player.

What’s wrong?

For digital copy-protection purposes, some 96 kHz/88.2 kHz

DVD discs only output digital audio downsampled to 48 kHz/

44.1 kHz. This is not a malfunction.

To fully take advantage of the high sampling rate audio, connect

the analog audio outputs to your amplifier/receiver.

• Why can’t I hear SACD audio through the digital outputs?

SACD digital audio is only available through the HDMI outputs

when connected to an HDMI-compatible amp that can handle

protected audio contents. Some DVD-Audio discs too only

output digital audio through the HDMI outputs.

• Is it better to listen to DVD-Audio discs through the analog

outp

uts?

me DVD-Audio discs do not output anything through the

digital outputs, and multichannel discs are downmixed to stereo

for the digital output. In addition, high sampling rate DVD-Audio

discs (higher than 96 kHz) automatically downsample audio

output from the digital outputs.

Using the multichannel analog audio outputs for DVD-Audio

have none of these limitations.

• My DVD-Audio disc starts playing, but then suddenly stops!

The disc may have been illegally copied.

• There’s no sound from the optical/coaxial outputs or the HDMI

interface!

Check the front panel and make sure that the PURE AUDIO

indicator isn’t lit. If it is, press the PURE AUDIO button to switch

the digital audio (optical/coaxial and HDMI) outputs back on.

You won’t hear any sound from the HDMI output if the source

component is only DVI/HDCP-compatible.

DV58AV_KU_EN.book 24 ページ２００７年８月３０日　木曜日　午後１時６分

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Pioneer DV58AV_KU_EN Manuel d'utilisateur Page 24

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de DVD Pioneer DV58AV_KU_EN