Pioneer KEH-P6020R Manuel d'utilisateur télécharger pdf (Page 3)

Connecting the Units

Fig. 5

Abb. 5

Afb. 5

10. Cap (1*)

When not using this terminal,

do not remove the cap.

17. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to

connect to both connectors.

23. System remote control

12. Yellow (2*)

To terminal always supplied

with power regardless of

ignition switch position.

14. Red (4*)

To electric terminal controlled

by ignition switch (12 V DC)

ON/OFF.

11. Yellow (3*)

Back-up

(or accessory)

13. Red (5*)

Accessory

(or back-up)

16. Black (ground)

To vehicle (metal) body.

15. Orange/white

To lighting switch terminal.

9. Connect leads of the same

color to each other.

22. Blue/white

To system control terminal of

the power amp (max. 300 mA

12 V DC).

6. Multi-CD player

(sold separately)

4. IP-BUS cable

24. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Note:

Depending on the kind of vehicle, the function

of 3* and 5* may be different. In this case, be

sure to connect 2* to 5* and 4* to 3*.

1. This Product

5. IP-BUS input (Blue)

3. Antenna jack

18. Yellow/black

If you use a cellular telephone, connect it via the

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connections.

2. Rear or Subwoofer output

7. Fuse

29. Rear Speaker

or Subwoofer

29. Rear Speaker

or Subwoofer

30. Perform these connections when using

a different amp (sold separately).

31.

19. Speaker leads

White

White/black

Gray

Gray/black

Green

Green/black

Violet

Violet/black

: Front left +

: Front left ≠

: Front right +

: Front right ≠

: Rear left + or Subwoofer +

: Rear left ≠ or Subwoofer ≠

: Rear right + or Subwoofer +

: Rear right ≠ or Subwoofer ≠

21. Power amp

(sold separately)

20. Connecting cords with RCA pin plugs

(sold separately)

27. Left 28. Right

25. Blue/white (6*)

26. The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and 7*

when Pin 5 is an antenna control type. In another

type of vehicle, never connect 6* and 7*.

Note:

When a subwoofer is connected to this unit

instead of a rear speaker, change the rear

output setting in the Initial Setting. (Refer to

the Operation Manual.)

The subwoofer output of this unit is

monaural.

• Cords for this product and those for other prod-

ucts may be different colors even if they have

the same function. When connecting this prod-

uct to another product, refer to the supplied

Installation manuals of both products and con-

nect cords that have the same function.

Note:

• This unit is for vehicles with a 12-volt battery

and negative grounding. Before installing it in a

recreational vehicle, truck, or bus, check the bat-

tery voltage.

• To avoid shorts in the electrical system, be sure

to disconnect the ≠ battery cable before begin-

ning installation.

• Refer to the owner’s manual for details on con-

necting the power amp and other units, then

make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch

any moving parts, such as the gear shift, hand-

brake and seat rails. Do not route wiring in

places that get hot, such as near the heater outlet.

If the insulation of the wiring melts or gets torn,

there is a danger of the wiring short-circuiting to

the vehicle body.

• Don’t pass the yellow lead through a hole into

the engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

• Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on this product.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded

or the left and right

≠ speaker leads are com-

mon.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and

impedance of 4 to 8 ohms. Connecting speakers

with output and/or impedance values other than

those noted here may result in the speakers

catching fire, emitting smoke or becoming dam-

aged.

• When this product’s source is switched ON, a

control signal is output through the blue/white

lead. Connect to an external power amp’s system

remote control or the car’s Auto-antenna relay

control terminal (max. 300 mA 12 V DC). If the

car features a glass antenna, connect to the anten-

na booster power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do

not connect the blue/white lead to the power ter-

minal of the auto-antenna. Such connection could

cause excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the

unused speaker leads without fail. There is a pos-

sibility of short-circuiting if the leads are not

insulated.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same col-

ors correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be con-

nected to a terminal coupled with ignition switch

ON/OFF operations. If this is not done, the vehi-

cle battery may be drained when you are away

from the vehicle for several hours.

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the

ground becomes detached, there is a risk of dam-

age to the products or fire.

Connecting the Units

Connection Diagram (Fig. 5)

1. This product

2. Rear or Subwoofer output

3. Antenna jack

4. IP-BUS cable

5. IP-BUS input (Blue)

6. Multi-CD player (sold separately)

7. Fuse

8. Note:

Depending on the kind of vehicle, the function of

3* and 5* may be different. In this case, be sure

to connect 2* to 5* and 4* to 3*.

9. Connect leads of the same color to each other.

10. Cap (1*)

When not using this terminal, do not remove the

cap.

11. Yellow (3*)

Back-up (or accessory)

12. Yellow (2*)

To terminal always supplied with power regard-

less of ignition switch position.

13. Red (5*)

Accessory (or back-up)

14. Red (4*)

To electric terminal controlled by ignition switch

(12 V DC) ON/OFF.

15. Orange/white

To lighting switch terminal.

16. Black (ground)

To vehicle (metal) body.

17. ISO connector

Note:

In some vehicles, the ISO connector may be

divided into two. In this case, be sure to connect

to both connectors.

18. Yellow/black

If you use a cellular telephone, connect it via the

Audio Mute lead on the cellular telephone. If not,

keep the Audio Mute lead free of any connec-

tions.

19. Speaker leads

White : Front left +

White/black : Front left ≠

Gray : Front right +

Gray/black : Front right ≠

Green : Rear left + or Subwoofer +

Green/black : Rear left ≠ or Subwoofer ≠

Violet : Rear right + or Subwoofer +

Violet/black : Rear right ≠ or Subwoofer ≠

20. Connecting cords with RCA pin plugs (sold

separately)

21. Power amp (sold separately)

22. Blue/white

To system control terminal of the power amp

(max. 300 mA 12 V DC).

23. System remote control

24. Blue/white (7*)

To Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

25. Blue/white (6*)

26.The pin position of the ISO connector will differ

depends on the type of vehicle. Connect 6* and

7* when Pin 5 is an antenna control type. In

another type of vehicle, never connect 6* and 7*.

27. Left

28. Right

29. Rear Speaker or Subwoofer

30. Perform these connections when using a different

amp (sold separately).

31. Note:

When a subwoofer is connected to this unit

instead of a rear speaker, change the rear output

setting in the Initial Setting. (Refer to the

Operation Manual.)

The subwoofer output of this unit is monaural.

ACC position

No ACC position

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Pioneer KEH-P6020R Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Autoradio Pioneer KEH-P6020R