Pioneer DEH-9300SD Manuel d'utilisateur télécharger pdf (Page 10)

<QRD3072-A> <10>

Connecting the units English Connecting the units English

Note

• When this unit is installed in a vehicle without

ACC (accessory) position on the ignition switch,

red cable must be wired to the terminal that can

detect the operation of the ignition key. Otherwise,

battery drain may result.

ACC position

No ACC position

• Use this unit in other than the following

conditions could result in fire or malfunction.

— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

• To prevent short-circuit, overheating or

malfunction, be sure to follow the directions

below.

— Disconnect

the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or

adhesive tape. To protect the wiring, wrap

adhesive tape around them where they lie

against metal parts.

— Place all cables away from moving parts, such

as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a

battery.

— Cover

any disconnected cable connectors with

insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power to other

equipment. Current capacity of the cable is

limited.

— Use

a fuse of the rating prescribed.

— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s

negative cables.

• Control signal is output through blue/white cable

when this unit is powered on. Connect it to an

external power amp’s system remote control or

the vehicle’s auto-antenna relay control terminal

(max. 300 mA, 12 V DC). If the vehicle is equipped

with a glass antenna, connect it to the antenna

booster power supply terminal.

• Never connect blue/white cable to external power

amp’s power terminal. Also, never connect

it to the power terminal of the auto antenna.

Otherwise, battery drain or malfunction may

result.

• Black

cable is ground. This cable and other

product’s ground cable (especially, high-current

products such as power amp) must be wired

separately. Otherwise, fire or malfunction may

result if they are accidentally detached.

Connection Diagram

1. This product

2. Rear output

3. Front output

4. Subwoofer output

5. Wired remote input

Hard-wired remote control adaptor can be

connected (sold separately).

6. Fuse (10 A)

7. Antenna jack

8. Notes

• Change the initial setting of this unit (refer

to the operation manual). The subwoofer

output of this unit is monaural.

• When using a subwoofer of 70 W (2 Ω), be

sure to connect with Violet and Violet/black

leads of this unit. Do not connect anything

with Green and Green/black leads.

9. Note

Depending on the kind of vehicle, the function

of 2* and 4* may be different. In this case, be

sure to connect 1* to 4* and 3* to 2*.

10. Connect leads of the same color to each other.

11. Yellow (2*)

Back-up (or accessory)

12. Yellow (1*)

Connect to the constant 12 V supply terminal.

13. Red (4*)

Accessory (or back-up)

14. Red (3*)

Connect to terminal controlled by ignition

switch (12 V DC).

15 Orange/white

Connect to lighting switch terminal.

16. Black (chassis ground)

Connect to a clean, paint-free metal location.

17. ISO connector

Note

In some vehicles, the ISO connector may

be divided into two. In this case, be sure to

connect to both connectors.

18. Yellow/black

If you use an equipment with Mute function,

wire this lead to the Audio Mute lead on that

equipment. If not, keep the Audio Mute lead

free of any connections.

19. Blue/white

Connect to system control terminal of the

power amp (max. 300 mA 12 V DC).

20.

Blue/white (6*)

Connect to auto-antenna relay control terminal

(max. 300 mA 12 V DC).

21. Blue/white (5*)

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect 5*

and 6* when Pin 5 is an antenna control type.

In another type of vehicle, never connect 5*

and 6*.

22. Speaker leads

White: Front left +

White/black: Front left *

Gray: Front right +

Gray/black: Front right *

Green: Rear left + or subwoofer +

Green/black: Rear left * or subwoofer *

Violet: Rear right + or subwoofer +

Violet/black: Rear right * or subwoofer *

23. To rear output

24. To front output

25. To subwoofer output

26. Power amp (sold separately)

27. Connect with RCA cables (sold separately)

28. System remote control

29. Subwoofer

30. Front speaker

31. Rear speaker

32. Perform these connections when using the

optional amplifier.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Pioneer DEH-9300SD Manuel d'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Multimédia automobile Pioneer DEH-9300SD