Pioneer BDP-LX91 Instructions d'exploitation télécharger pdf (Page 66)

• Picture is stretched.

• Picture is cropped.

• Aspect ratio cannot be

switched.

Is the TV’s aspect ratio properly set? Read the TV’s operating instructions and set the TV’s aspect

ratio properly.

Is TV Aspect Ratio properly set? Set TV Aspect Ratio properly (page 43).

Is 4:3 Video Out properly set? Set 4:3 Video Out properly (page 43).

Is DVD 16:9 Video Out properly set? Set DVD 16:9 Video Out properly (page 43).

When video signals with a resolution of 1080/50i, 1080/50p, 720/

50p, 1080/24p, 1080/60i, 1080/60p or 720/60p are being output

from the

HDMI OUT

terminals or the

COMPONENT VIDEO

output terminals, they may be output with an aspect ratio of

16:9 even if

TV Aspect Ratio

is set to

4:3 (Standard)

(page 43).

Is Anamorphic Zoom set to On?Set Anamorphic Zoom to Off (page 51).

Picture is interrupted. The picture may be interrupted when the resolution of the

recorded video signal switches. Press OUTPUT RESOLUTION

to select a setting other than Auto, 1080/24p or Source Direct

(page 24).

Sound and picture are not

synchronized.

Is Output Terminal properly set? Set Output Terminal properly (pages 20 and 43).

Is Lip Sync properly set? Adjust the amount of audio delay with the Lip Sync setting

(page 41).

• No sound is output.

• Sound is not output

properly.

Is the disc played back in slow motion?

Is the disc played back in fast forward or fast reverse?

No sound is output during slow motion play and forward and

reverse scanning.

Are the audio cables properly connected? • Connect the cable properly according to the connected

devices (page 14).

• Insert the cable firmly and all the way in.

Is the audio cable damaged? If the cable is damaged, replace it with a new one.

Are the connected components (AV receiver or amplifier, etc.)

properly set?

Read the operating instructions of the connected components

and check the volume, input, speaker settings, etc.

Is Output Terminal properly set? When ANALOG AUDIO is selected at Output Terminal, no

audio signals are output from the HDMI OUT or DIGITAL OUT

terminals (page 43).

Is the output video resolution properly set? Use OUTPUT RESOLUTION to switch to the resolution at

which the video and audio signals are output (page 24).

Is the AV receiver or amplifier, etc., connected to the AUDIO

OUT (7.1 ch) terminals?

To listen to 2-channel analog audio, connect to FRONT (L/R) of

the AUDIO OUT (7.1 ch) terminals (page 13) and set Audio

Output Mode to 2 Channel (page 44).

Are the speakers properly set? When the AV receiver or amplifier, etc., is connected to the

AUDIO OUT (7.1 ch) terminals and Audio Output Mode is

set to Multi-channel, set Speaker Setup properly (page 46).

Is Pure Audio set to Mode 1 or Mode 2? If set to Mode 1 or Mode 2, signals are only output from the

output terminal set at Output Terminal (page 52).

Is a DVI device connected?

The sound will not be output from the

HDMI OUT

terminals if a

DVI device is connected. Connect the device to a

DIGITAL OUT

terminals or the

AUDIO OUT (7.1 ch)

terminals (page 17).

Are you playing a DTS-CD? To output the sound of DTS-CDs from the HDMI OUT (SUB)

terminal, set HDMI Audio Out to PCM (page 44).

For some BDs, audio signals are only output from DIGITAL

OUT terminals or the HDMI OUT terminals.

Multi-channel sound is not

output.

Is Output Terminal properly set? Linear PCM (2-channel) audio signals are output from output

terminals other than the one set at Output Terminal under

Audio Out. Set Output Terminal properly (page 43).

Is the AV receiver or amplifier connected to the HDMI OUT

(SUB) terminal?

The HDMI OUT (SUB) terminal outputs linear PCM 2-channel

audio signals. Be sure to connect the AV receiver or amplifier

to the HDMI OUT (MAIN) terminal.

Is the audio output of the connected AV receiver or amplifier,

etc., properly set?

Read the operating instructions of the connected AV receiver

or amplifier and check the audio output settings of AV receiver

or amplifier.

Is multi-channel sound selected? Use the menu screen or AUDIO to switch the disc’s sound to

multi-channel.

Is the AV receiver or amplifier, etc., connected to the AUDIO

OUT (7.1 ch) terminals?

When the AV receiver or amplifier, etc., is connected to the

AUDIO OUT (7.1 ch) terminals, set Audio Output Mode to

Multi-channel (page 44). Also, set Speaker Setup properly

(page 46).

Problem Check Remedy

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 72 73

Commentaires sur ces manuels

Pas de commentaire

Pioneer BDP-LX91 Instructions d'exploitation Page 66

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de Blu-Ray Pioneer BDP-LX91