Pioneer BDP-LX52 Manuel d'utilisateur télécharger pdf (Page 56)

No picture is displayed or the

picture is not displayed

properly.

Is the video cable properly

connected?

• Connect the cable properly according to the connected devices

(page 13).

• Insert the cable firmly and all the way in.

Is the video cable damaged? If the cable is damaged, replace it with a new one.

Is the input setting on the

connected TV or AV receiver

or amplifier right?

Read the operating instructions of the connected components and

switch to the proper input.

Are you viewing the picture

from the video output

terminal selected with VIDEO

SELECT?

Press VIDEO SELECT to switch the video output terminal to be viewed

(page 21).

Is the output video resolution

properly set?

Use OUTPUT RESOLUTION to switch to a resolution at which the video

and audio signals are output (page 21).

• Is the player connected

with an HDMI cable other

than a High Speed HDMI™

cable (with a Standard

HDMI™ cable)?

• Are you using an HDMI

cable with built-in equalizer?

1080p or Deep Color video signals may not be output properly,

depending on the HDMI cable being used or the player’s settings.

Press  while pressing  on the player’s front panel to restore the

video outputs to the factory default settings. After this, if you wish to

output the video signals with 1080p or Deep Color, connect the TV

using a High Speed HDMI™ cable without built-in equalizer, then reset

the player using the Setup Navigator (page 18).

Does the connected TV

support the frame rate of the

video signal being output by

the player?

If the picture is not displayed when playing a disc with a frame rate that

is not supported, the picture will not be displayed even when playback

is stopped. In this case, use the procedure below to switch the frame

rate of the video signals output from the player.

Eject the disc and close the disc tray. Then, press  OPEN/CLOSE

while pressing  on the player’s front panel to switch to a frame rate

supported by the connected TV.

Is NTSC on PAL TV properly

set?

When viewing the video signals output from the player’s S-Video or

Video terminal, set NTSC on PAL TV properly (page 37).

Is a DVI device connected? The picture may not be displayed properly if a DVI device is connected.

Is HDMI Color Space

properly set?

Change the HDMI Color Space setting (page 38).

Picture freezes and the front

panel and remote control

buttons stop working.

• Press  STOP to stop playback, then restart playback.

• If the playback cannot be stopped, press  STANDBY/ON on the

player’s front panel to turn off the power, then turn the power back on.

• If the power cannot be turned off, press and hold  STANDBY/ON

on the player’s front panel for over 5 seconds. The power will turn off.

Motion is unnatural or

picture is not clear.

Change the Pure Cinema sett

ing (page 34).

No picture is displayed or

picture is not output in high

definition when playing BDs.

With some discs, it may not be possible to output the video signals from

the

VIDEO

output terminal or the

COMPONENT VIDEO

output

terminals. In this case, connect using an HDMI cable (page 13).

• Picture is disturbed during

playback.

• Picture is dark.

• This player supports Macrovision analog copy protection technology.

With some TVs (such as with built-in video deck), the picture will not be

displayed properly when the copy protected DVD title is played. This is

not a malfunction.

• If the player and TV are connected via a DVD recorder/video deck,

etc., the picture will not be displayed properly due to analog copy

protection. Connect the player and TV directly.

Problem Check Remedy

LX52_VXJ5_IBD_EN.book 56 ページ２００９年３月３日　火曜日　午後７時２９分

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 62 63 64

Commentaires sur ces manuels

Pas de commentaire

Pioneer BDP-LX52 Manuel d'utilisateur Page 56

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de Blu-Ray Pioneer BDP-LX52