Pioneer Elite VSX-91TXH Manuel d'utilisateur télécharger pdf (Page 53)

Other connections

HDMI, the logo and High-Definition

Multimedia Interface are trademarks or registered

trademarks of HDMI licensing LLC.

Connecting the multichannel analog

inputs

For DVD Audio and SACD playback, your DVD player may

have 5.1, 6.1 or 7.1 channel analog outputs (depending

on whether your player supports surround back

channels).

Make sure that the player is set to output

multichannel analog audio.

1 Connect the front, surround, center and subwoofer

outputs on your DVD player to the corresponding

MULTI CH input jack on this receiver.

• Use standard RCA/phono jack cables for the

connections.

2 If your DVD player also has outputs for surround

back channels, connect these to the corresponding

MULTI CH input jacks on this receiver.

• Use standard RCA/phono jack cables for the

connections.

• If there is a single surround back output, connect it to

the SURROUND BACK L (Single) jack on this

receiver.

Selecting the multichannel analog inputs

If you have connected a decoder or a DVD player as

above, you must select the analog multichannel inputs

for surround sound playback.

1 Make sure you have set the playback source to the

proper output setting.

For example, you might need to set your DVD player to

output multichannel analog audio.

2Press

MULTI CH IN

(front panel).

• Depending on the DVD player you’re using, the

analog output level of the subwoofer channel may be

too low. In this case switch the receiver into standby,

then press  STANDBY/ON while holding down

SBch PROCESSING on the front panel. This switches

between SW IN +10dB (increase of 10 decibels) and

SW IN 0dB (default) in the subwoofer channel.

Speaker B setup

Caution

• Before making or changing the connections, switch off

the power and disconnect the power cord from the

power outlet. Plugging in components should be the

last connection you make with your system.

• Be careful not to allow any contact between speaker

wires from different terminals.

• You can use speakers with a nominal impedance

between 6 Ω to 16 Ω (please see Switching the

speaker impedance on page 65 if you plan to use

speakers with an impedance of less than 8 Ω).

After selecting Speaker B in Surround back speaker

setting on page 36, you can use the speakers connected

to the (surround back) B speaker terminals on the rear

panel to listen to stereo playback in another room. See

Switching the speaker system below for the listening

options with this setup.

1 Connect a pair of speakers to the surround back

speaker terminals on the rear panel.

Connect them the same way you connected your

speakers in Installing your speaker system on page 17.

Make sure to review Placing the speakers on page 18

when placing the speakers in another room.

2Select ‘

Speaker B

’ from the ‘Surr Back System’

menu.

See Surround back speaker setting on page 36 to do this.

Switching the speaker system

If you selected Speaker B in Surround back speaker

setting on page 36, three speaker system settings are

possible using the SPEAKERS button. If you selected

Normal (SB) or Front Bi-Amp, the button will simply

switch your main speaker system on or off. The options

below are for the Speaker B setting only.

• Use the SPEAKERS button on the front panel to

select a speaker system setting.

As mentioned above, if you have selected Normal (SB),

the button will simply switch your main speaker system

(A) on or off.

Press repeatedly to choose a speaker system option:

• SPA – Sound is output from speaker system A and

the same signal is output from the pre-out terminals.

Note

1 To listen to multichannel analog audio you’ll need to select MULTI CH IN (see Selecting the multichannel analog inputs above for more on this).

2 • When playback from the multichannel inputs is selected, you can’t use the sound processing features, SIGNAL SELECT, or any of the listening modes

(including STEREO and the surround back channel processing).

• When playback from the multichannel inputs is selected, only the volume and channel levels can be set.

• You can’t listen to your speaker B system during playback from the multichannel inputs.

3 • The subwoofer output depends on the settings you made in Manual speaker setup on page 43. However, if SPB is selected above, no sound is heard

from the subwoofer (the LFE channel is not downmixed).

• Depending on the settings in Surround back speaker setting on page 36 output from the surround back pre-out terminals may change.

• All speaker systems (except Speaker B connections) are switched off when headphones are connected.

VSX-91TXH_KU.book Page 53 Friday, March 16, 2007 5:31 PM

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 87 88

Commentaires sur ces manuels

Pas de commentaire

Pioneer Elite VSX-91TXH Manuel d'utilisateur Page 53

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Pioneer Elite VSX-91TXH