Pioneer PDK-50HW3 Manuel d'utilisateur

HANDWRITING DEVICE: PDK-50HW3Supported plasma displays: PDP-504CMXPDP-503CMXPDP-50MXE1PDP-50MXE1-SPDP-503MXEABOUT MOUNTING/INSTALLATION÷ This product

101. Specifications<Rear panel>PEN-NORMAL mode selector switch (in lower left corner as seen from rear)NP1466693 3322Plasma display side panel22

111. Specifications1.4 Name and Function of Parts & Pin Layout1.4.1 Plasma display monitor (PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S)For information o

122.1 Installation SiteThe installation site precautions for the handwriting device are the same as those for the PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S.

132. Installation Site2.2.2 Special installationsSpecial installation conditions for the handwriting device are the same as for the plasma display. R

142. Installation Site2.2.3 Installation precautionsa) Installation of multiple systemsSince the dedicated handwriting pen of the system is designed t

153.1 Unpacking3.1.1 Plasma display monitor (PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S)¶ Any transportation of the unopened unit in its packaging should be

163. Installation Procedures3.1.2 Handwriting device (PDK-50HW3)Transportation precautions¶ Do not stack more than four boxes on top of each other. S

173. Installation Procedures3.2 Assembly and Connections3.2.1 Installing the handwriting device (PDK-50HW3) Notes:¶ Always install the plasma displ

183. Installation Procedures3. Use the locking fixture on the rear panel to secure the four corners of scan device.1 Rotate the locking fixture in the

193. Installation Procedures3.2.3 Connecting the plasma display to a computerFor information on connecting the plasma display to a computer, refer to

2Scan device changesa) The Pioneer badge need no longer be removed during installation.¶ In this manual, the frame of the handwriting device that hous

203. Installation Procedures3.4 Adjusting the Plasma Display3.4.1 Procedures for setting the plasma displayFor details, refer to the Technical Manua

213. Installation Procedures3.4.2 Screen burningRefer to “Screen Burning” in the Technical Manual supplied with the plasma display.3.5 Installing th

223. Installation Procedures3.7 How to Use Cable ClipUse the cable clip to hold the unit's USB cable.USB cableCable clip3.8 Sensor Operation Ch

233. Installation ProceduresPen tipMouse cursor (screen display position) ¶ Alignment of pen tip and cursor positionConfirm that the onscreen cursor a

243. Installation Procedures5. Start up the utility software (“MSpaint.exe” if CBLink is not installed).6. Slowly draw oblique lines across the screen

254.1 Installing the CBdrvU (Ver. 2.0) Driver*Supplied with PDK-50HW34.1.1 Operating environmenta) Operating environment¶ Supported plasma displays:

264. Installing and Using Software4.1.3 Uninstall proceduresUse the following procedures to uninstall the installed CBdrvU software.Use this procedur

274. Installing and Using Software2. Left-click on the CBdrvU icon in the task tray to open the pop-up menu shown below.[Overview]Current Resolution:

284. Installing and Using Softwarec) Scan device setup screenThis screen appears during scan device setup. (This screen closes automatically when setu

294. Installing and Using Software[Overview]Easy Setting: Apply preset calibration by specifying currently displayed screen mode.The following modes a

3Changes from PDK-50HW2A to PDK-50HW32. Device depth has been reduced for a slimmer look.80(excluding screw heads)]PDK-50HW2A PDK-50HW3(excluding scre

304. Installing and Using Softwareb) Calibration (Detail-2)When the plasma display is in the “PARTIAL” mode, use the mouse to click the two points, th

314. Installing and Using Software4.2.3 Property screenMake settings for the pen in this screen.[Sheet function overview]Double-click area: Set effec

324. Installing and Using Softwareb) Double-click speedSet pen double-click speed. Notes:¶ Screen appearance varies with computer environment.¶ Adjus

334. Installing and Using Software4.2.4 Test ModeThis is a service mode. Click “Test Mode” under “Hardware Information” in the CBdrvU task tray to op

344. Installing and Using Software4.2.5 Disabling CBdrvUEnable/disable CBdrvU.a) Disabling CBdrvUChecking the “Disable CBdrvU” checkbox displays the

354. Installing and Using Software4.3 Rotate4.3.1 CBdrvU operationA video card enabling screen rotation is required for this function.a) Task tray d

364. Installing and Using Software4.4 Precautionsa) Use of video cards other than recommendedA video card other than those recommended for use with C

374. Installing and Using Software Notes:¶ Set the rotate angle to 90° in Property screen when the plasma display is to be set up in the standard set

384. Installing and Using Software4.5 Using Driver and Service Mode4.5.1 Service Mode displayPress the Service Mode button in the “Test Mode” screen

394. Installing and Using Software2. When all components of test board D (LED) and all components of test board K (Sens) are malfunctioning.The detail

4Changes from PDK-50HW2A to PDK-50HW3Pen stand modificationsa) The pen stand has been modified.The fitting is now more durable, but it is attached to

40Periodical maintenance is recommended to improve the service life and performance of the system. In themaintenance, clean the system equipment as de

415. Maintenance and Cleaninge) Replacing the pen tipIf the tip becomes deformed and writing quality deteriorates, replace the tip with one of the two

42The test board A (LED) in the device is provided with 8-bit DIP switches (SW1).DIP switch settings are read only when the device is powered up and t

437.1 Hardware-Related Q&AQ: Which is the touch panel system?A: It is based on the IR scan system.Q: Which is the advantage of the IR scan system

447. Q & AQ: Is tempered glass used in the plasma display screen?A: No, but the screen has an AR coating that will prevent broken glass from scatt

457. Q & AQ: Can the PDK-5008 mobile cart be used?A: No, since it does not remain stable during writing. Use of the PDK-5009, PDK-5014, PDK-MC01 i

467. Q & AQ: Is there a convenient way for adjusting the plasma display monitor?A: With the PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S, adjustments are po

47If you think there is something wrong with this component, check the details in the following table. Sometimes anothercomponent may be the cause of

488. TroubleshootingProblem• Stripes appear on thescreen.• Sound is heard frominside the unit.• Fan isn’t moving.• Fan speed changes.• ON (green) indi

498. Troubleshooting8.2 Handwriting Device (PDK-50HW3)SymptomNo powerNo response when operated.USB cable is not recognized bycomputer when connected.

5Changes from PDK-50HW2A to PDK-50HW3e) SXGA (1280 x 1024) 4:3 preset values have been added.f) Test Mode indication has been changed.]PDK-50HW2A PDK-

509.1 IR Scanning SystemThe handwriting device scans IR rays in the horizontal and vertical directions to detect the coordinate positions.There are 2

51

61. Specifications... 71.1 Specifications ...

71.1 SpecificationsSystem (plasma display and handwritingdevice) specificationsScreen size 50 inchesAspect ratio 16:9Power supplyPlasma display (PDP-

81. Specifications1.2 Accessories1.2.1 Plasma display monitor (PDP-504CMX/PDP-50MXE1/PDP-50MXE1-S)Check that the following accessories were supplied

91. Specifications1.3 Outline DrawingSystem weight: 48.4 kg (plasma display (PDP-504CMX) 41.0 kg plus handwriting device 7.4 kg)Materials: Front pane