Pioneer PDP 427CMX Manuel d'utilisateur

PLASMA DISPLAY MONITOR: PDP-507CMX/PDP-427CMXVIDEO CARD: PDA-5003/PDA-5004TABLE TOP STAND: PDK-TS07TILT MOUNT UNIT: PDK-5011WALL MOUNT UNIT: PDK-WM01C

10External DimensionsPDP-427CMXWEIGHT: 30.5 kg (67.3 lbs) (without stand)MATERIAL: Front: Resin; Rear cover: Metal plate, Front protector panel: Glass

1004.5.4 Stand assembling1) Assembling Steps1 Turn the base cover over so that the bottom is facing up.2 Insert the stand pipes into the base cover.3

101Table Top Stand: PDK-TS074.5.5 Attaching the Stand to the Plasma DisplayThe Plasma Display is heavy, has no depth, and isunstable, so be sure to ha

102Table Top Stand: PDK-TS07After attachment, take measures to prevent it fromfalling over.7 Using a wall for stabilization1 Attaching the accessory f

103Table Top Stand: PDK-TS07[507CMX : 427CMX]

104Tilt Mount Unit: PDK-50114.6 Tilt Mount Unit: PDK-50114.6.1 SpecificationsExternal dimensions ... 1222 mm (W) × 736 mm (H) × 144 mm (

105Tilt Mount Unit: PDK-50114.6.2 External Dimensions7 When using Plasma Display PDP-507CMX(Units: mm)99(183)353535150 1507366-ø10.5(55)65555545549674

1065 Attach the wall side hardware to the wall.Install the wall side hardware (four locations) symmetri-cally on the left and right side (one at each

107Tilt Mount Unit: PDK-5011HookClosingOpening6 Attach the hook on the PDP side hardware to the wallside hardware.NoteDo not hold the speakers during

108Tilt Mount Unit: PDK-5011OpeningClosingHexagon wrenchMeasuring the opening distanceX provides an approximate anglevalue.XWhen it is in this state,

109Tilt Mount Unit: PDK-50114.6.5 Measure to prevent shakiness when the unit is installed at a slight tiltWith this installation hardware, for structu

11<Main Unit Operation Panel> <Light Sensor for the remote/ambient lightsensor/indicator>External Dimensions<Connection panel>30.310

1104.7 Wall Mount Unit: PDK-WM014.7.1 SpecificationsExternal dimensions ... 1222 mm (W) × 736 mm (H) × 131 mm (D) (48-1/8 in. (W) × 28-31/

111Wall Mount Unit: PDK-WM014.7.2 External Dimensions7 When using Plasma Display PDP-507CMX (Unit: mm)27141 120910540496455197197120 141736(425)150 15

112Wall Mount Unit: PDK-WM014.7.3 Assembling the mounting hardware andmounting the display1 Remove the push rivet of the lock plate and the bottomanch

113Wall Mount Unit: PDK-WM016 Hang the hook of the PDP side metal fitting on thewall side metal fitting1 Hang the hook on the ceiling surface part of

114Wall Mount Unit: PDK-WM018 With the lock bar in the lock position, fix the lock platefirmly in place with push rivet and the anchor screw(M6 x 14 m

115Wall Mount Unit: PDK-WM014 Raise the lock bar then pull the bottom of the PlasmaDisplay forward.Pull out the bottom ofthe Plasma Display.5 Raise to

116Ceiling Mount Unit: PDK-50124.8 Ceiling Mount Unit: PDK-50124.8.1 SpecificationsExternal dimensions ... 1222 mm (W) × 1168 mm (H) × 3

117Ceiling Mount Unit: PDK-50124.8.2 External Dimensions7 When using Plasma Display PDP-507CMX(Unit: mm)R673R61645°45°736496(530)1222300980800ø60.54-ø

118[507CMX : 427CMX]Ceiling Mount Unit: PDK-50127 When using Plasma Display PDP-427CMX(Unit: mm)R580R51045°45°4-φ13.5X221299847 10621106780277(493)329

119Ceiling Mount Unit: PDK-5012Ceiling suspension hardwareAnchorFoundation ceilingSafety wireBolt(NOTE) Safety wires serve as important backups in kee

1215STANDBYONSTANDBY/ON MENUDISPLAY/ SET– VOL +INPUT SCREEN SIZE7 8= 9 06342-2.3 Controls and ConnectorsControls and ConnectorsMain unitOperation pane

120Ceiling Mount Unit: PDK-50124.8.4 Attach the Plasma Display1 Attach the PDP bracket to the Plasma Display.Note• Place a sheet or protective cover t

121Ceiling Mount Unit: PDK-50125°10°15°20°4.8.5 Angle setupLeft-right AdjustmentYou can adjust it 45° to the left or right by loosening thetop screw.S

1224.9 Mobile Cart: PDK-50144.9.1 SpecificationsExternal dimensions ... 1 1222 mm (W) × 1718 mm (H) × 710 mm (D)(48-1/8 in. (W) × 67-5/8

123Mobile Cart: PDK-50144.9.2 External Dimensions7 When using Plasma Display PDP-507CMX(Units: mm)Note: Dimensions1 : Compatible with Serial Nos. 1 to

124Mobile Cart: PDK-5014 [507CMX : 427CMX]7 When using Plasma Display PDP-427CMX(Units: mm) (Stand shelf)10065305510049690180124 66759600630660120920

1254.9.3 Disassembling the display stand1 Remove the screws (four locations on the left and rightsides) then take off the bracket. For packing reasons

126Mobile Cart: PDK-5014BracketPlasma DisplayHexagonal bored bolts(M8 × 20 mm)Top side of Plasma Display2 Attach bracket bolts to display standAttach

127To safely attach the brackets to the support columns,be sure to always have two people do this task asshown in the drawing.[Adjusting the angle of

1286 Adjust the support caster. When the mobile cart hasbeen placed into position, be sure to adjust the supportcaster to fix into place.1. Turn the s

129[507CMX : 427CMX] Mobile Cart: PDK-5014

13Controls and ConnectorsConnection Panel (PDP-507CMX)Plasma Display Section1 SPEAKER (R) terminalFor connection of an external right speaker.Connect

130PDP Bracket: PDK-50054.10 PDP Bracket: PDK-5005(Can be used only with the PDP-507CMX)4.10.1 SpecificationsExternal Dimensions ... 1222 mm (W

131PDP Bracket: PDK-50054.10.2 External Dimensions(Units: mm)The mounting format is symmetrical from left to right and from top to bottom.828122279845

1324.10.3 Assembly Procedure1 Temporarily fasten the vertical a and horizontal b frames using all of the M5 plus/minus screws with washers e.2 Attach

1333 Place the bracket on a level table or platform for the final tightening of the bolts.<Wrong>Table, etc.If placed in this position, it will

134PDP Bracket: PDK-5005Use the Special eye bolt only at the specified locations.Improper use of Special eye bolts within the Plasma Display main body

135PDP Bracket: PDK-5005[507CMX]

136Speaker System: PDP-S53-LR4.11 Speaker System: PDP-S53-LR(Can be used only with the PDP-507CMX)4.11.1 SpecificationsExternal dimensions ...

1374.11.2 External Dimensions (when mounted to the Plasma Display)Unit: mm (inch)Speaker System: PDP-S53-LR1403 (55-1/4)90 (3-17/32) 90 (3-17/32)58 (2

138Speaker System: PDP-S53-LR4.11.3 Installation on the Plasma Display1) Installation procedureInstall the speaker system according to the steps (1)th

139Speaker System: PDP-S53-LR2) Connect the cords(Turn off the power of all connected units beforeconnecting the cords.)Use the provided speaker cords

14Controls and ConnectorsVideo Card <PDA-5004> SectionThe video card provides three video input connectors,one video output connector, and three

140Speaker System: PDP-S56-LR4.12 Speaker System: PDP-S56-LR(Can be used only with the PDP-427CMX)4.12.1 SpecificationsExternal dimensions ...

141[427CMX] Speaker System: PDP-S56-LR4.12.2 External Dimensions (when mounted to the Plasma Display)Units: mm (inch)1204 (47-13/32)90 (3-17/32)90 (3-

142Speaker System: PDP-S56-LR [427CMX]4.12.3 Installation on the Plasma Display1) Installation procedureInstall the speaker system according to the st

143[427CMX] Speaker System: PDP-S56-LR2) Connect the cords(Turn off the power of all connected units beforeconnecting the cords.)Connect the display’s

144Before Beginning Adjustment/Setting5.1 Before Beginning AdjustmentThere are three methods for adjusting this display:• Main control panel• Remote c

145Before Beginning Adjustments3 Integrator ModeThis mode provides an adjustment function for integrator options.This mode has white-balance adjustmen

146Before Beginning Adjustments5.1.3 List of Input Correspondence Signals1) Input correspondence signals (personal computer signals)INPUT1[PDP-507CMX]

147Before Beginning AdjustmentsINPUT2[PDP-507CMX]Resolution(Dot x Line)VerticalDOT BY DOTFULLRemarksScreen size (Dot x line)Horizontal4:3Refresh rateR

148Before Beginning AdjustmentsResolution(Dot x Line)VerticalDOT BY DOT FULLRemarksScreen size (Dot x line)Horizontal4:3: Not available.Refresh rate :

149Before Beginning AdjustmentsINPUT1[PDP-427CMX]: Not available.DOT BY DOTFULLRemarksScreen size (Dot x line)4:3VerticalHorizontalRefresh rateResolut

15S-VIDEOS-VIDEOOUT R LRL RL RLY Pb/Cb Pr/CrIN OUTBR VD RLHD (H/V SYNC)G(ON SYNC)INPUT3INPUT3 INPUT4 INPUT5VIDEOINPUT4INPUT 3/4 ANALOG RGB AUDIOAUDIOA

150Before Beginning AdjustmentsResolution(Dot x Line)VerticalDOT BY DOTFULLScreen size (Dot x line)Horizontal4:3Refresh rate : Optimal picture. Adjust

151Before Beginning AdjustmentsResolution(Dot x Line)VerticalDOT BY DOT FULLRemarksScreen size (Dot x line)Horizontal4:3: Not available.Refresh rate :

152Before Beginning Adjustments2) Screen sizeScreen sizePersonal computer signalRemarksFULLThis is for wide-screen video (squeeze) (For a 16:9 source,

1533) Input correspondence signals (video signals) ★ (Applicable only when a PDA-5003/PDA-5004 is installed.)INPUT1, INPUT5 ★: Not available.15.62528.

154Before Beginning AdjustmentsINPUT4 ★Signal FormatCompositeCompositeCompositeCompositeCompositeComposite4 : 3 FULL ZOOM WIDE CINEMA 14:9 2.35:1Remar

1554) Input correspondence signals (personal computer signals)INPUT1, INPUT5 ★ (Applicable only when a PDA-5003/PDA-5004 is installed.)[PDP-507CMX]: N

156Before Beginning AdjustmentsINPUT2[PDP-507CMX]Resolution(Dot x Line)VerticalDOT BY DOTFULLRemarksScreen size (Dot x line)Horizontal4:3Refresh rateR

157Before Beginning AdjustmentsResolution(Dot x Line)VerticalDOT BY DOT FULLRemarksScreen size (Dot x line)Horizontal4:3: Not available.Refresh rate :

158Before Beginning AdjustmentsINPUT1[PDP-427CMX]: Not available.DOT BY DOTFULLRemarksScreen size (Dot x line)4:3VerticalHorizontalRefresh rateResolut

159Before Beginning AdjustmentsResolution(Dot x Line)VerticalDOT BY DOTFULLScreen size (Dot x line)Horizontal4:3Refresh rate : Optimal picture. Adjust

16Controls and ConnectorsVideo Card <PDA-5004> SectionThe video card provides 3 video input connectors, 1video output connector and 3 audio inpu

160Before Beginning AdjustmentsResolution(Dot x Line)VerticalDOT BY DOT FULLRemarksScreen size (Dot x line)Horizontal4:3: Not available.Refresh rate :

161Before Beginning Adjustments5) Screen sizeWhen a video card is installedVideo signal 4:3 source (NTSC, 625i, etc.)Video signal 16:9 source (750p,

162Before Beginning Adjustments5.1.4 List of Adjustable and Settable Items1) Menu Mode7 PDP-507CMX/PDP-427CMX*1: INPUT1 case*2: INPUT2 case(Note 1) Th

1637 PDP-507CMX/PDP-427CMX★★: Applicable only when a PDA-5003/PDA-5004 is installed.: Cannot be set according to the signal.*1: INPUT1 case*2: INPUT2

164Before Beginning Adjustments7 PDA-5003/PDA-5004★: Applicable only when a PDA-5003/PDA-5004 is installed.: Cannot be set according to the signal.*1:

165Before Beginning Adjustments7 Slot card other than PDA-5003/PDA-5004★: Applicable only when a video card is installed.: Cannot be set according to

166Before Beginning Adjustments2) Integrator mode7 PDP-507CMX/PDP-427CMX(Note) The OPTION settings are common settings for all inputs.

167Before Beginning Adjustments7 PDP-507CMX/PDP-427CMX★: Applicable only when a PDA-5003/PDA-5004 is installed.(Note) The OPTION settings are common

168Before Beginning Adjustments7 PDA-5003/PDA-5004: INPUT3 to INPUT5 are applicable only when the PDA-5003 or the PDA-5004 is installed.(Note) The O

169Before Beginning Adjustments7 Slot card other than PDA-5003/PDA-5004: INPUT3 to INPUT5 are applicable only when the PDA-5003 or the PDA-5004 is in

172.4 Pin layoutINPUT1 (Mini D-sub, 15-pin connector; female)pin layoutPin No.Signal1 NC (not connected)2 TxD (Transmit Data)3 RxD (Receive Data)4 NC

170Operation in the normal-operation mode• Power ON/OFF• Switching input• Switching screen size• Volume adjustment• FUNCTIONAL LOCK settingAdjustments

171Normal Operating Mode5.2 Normal Operation Mode5.2.1 About normal operation modeThe following controls are possible in the normal operation mode.1 S

172Normal Operating Mode4 Volume Adjustment/Muting• Pressing the [VOLUME+] button on the remote control or main-control panel raises the volume.• Pres

173Menu Mode5.3 Menu Mode5.3.1 About menu mode1) Entering/leaving the menu mode• Pressing the [MENU] button on the remote control or main-control pane

174Menu Mode5.3.3 Example of a Menu Mode OperationThe basic operation in the menu mode will be explainedusing brightness adjustment as an example.1 Pr

175Menu Mode5.3.4 Adjustment and setting in the Menu Mode1) Power Management SettingWhen no video signal (synchronizing signal) is detected, this func

176Menu Mode2) Signal Format SettingThis display automatically identifies PC signals and video signals such as from a DVD player by the frequency of t

177Menu Mode3) Menu Language Display SettingThe factory setting for the menu display language is English. To change to another language, set the selec

178Menu ModeSTANDARD1, STANDARD2 (STANDARD)*For an overall bright video, there is no change(Figure on the left).For an overall dark video, the peak br

179Menu Mode1 Select ‘OPTION’.2 Place the cursor over ‘ENERGY SAVE’ then press the [SET]button to change the setting.Each time the [SET] button is pre

182.5 Remote Control UnitRemote Control Unit1 SCREEN SIZE buttonPress to select the screen size.2 INPUT buttonsPress to select the input.3 MENU button

180Menu Mode5) Timer SettingThe present day of the week, time, and daylight savings time are set.1 Select ‘OPTION’.2 Place the cursor on ‘TIMER SETTIN

181Menu Mode7) Orbiter SettingThis function gradually moves the display position of the screen periodically screen position is moved at random,horizon

182Menu Mode8) Soft Focus SettingImages are softened by suppressing the edge contrast.Factory setting: OFF1 Select ‘OPTION’.2 Place the cursor on ‘SCR

183Menu Mode9) Auto Set Up Mode SettingThis function automatically adjusts the signal when the power is turned ON, when the input is changed, and when

184Menu Mode10) Screen Position, Clock Frequency and Clock Phase AdjustmentIn AUTO SET UP, the position and clock are optimally set. However, dependin

185Menu Mode6 Use the [2/3] buttons to adjust the click frequency.In step 4, the left side was aligned while here the rightside is aligned.1. With the

186Menu Mode11) Auto Function Mode SettingWith the Auto Function mode it is possible to automatically change the input when a signal is detected.Facto

187Menu Mode12) PIP DETECT SettingDuring picture-in-picture display, if no subscreen input signal is detected then the black borders of the subscreen

188Menu Mode13) SPLIT FREEZE SettingFor setting other than [OFF], the image displayed when the FREEZE button is pressed is displayed in a subscreen as

189Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]5.3.6 Example of a Menu Mode Operation(Applicable only when a PDA-5003/PDA-5004 is

192.6 Remote Control Unit Holder (PDP-427CMX only)Peel the sticker covers from the lower and upper mounting tapes on the rear of the remote control ho

190Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]5.3.7 Adjustment and setting in the Menu Mode(Applicable only when a PDA-5003/PDA-

191Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]2) Power Management and Auto Power OFF SettingWhen no video signal (synchronizing s

192Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]3) DNR (digital noise reduction) SettingThe DNR (digital noise reduction) setting

193Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]4) MPEG NR SettingThis is set when the noise (mosquito noise) of the video such as

194Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]5) CTI SettingThis setting sharpens the color contours as desired.The setting shou

195Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]6) PURECINEMA SettingThe PURECINEMA function automatically detects video signals su

196Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]Input Correspondence SignalINPUT1, INPUT5INPUT3, INPUT428.1331.2537.5031.533.7545.

197Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]7) Color Decoding SettingWhen a video signal is input at INPUT1, INPUT2 and INPUT5,

198Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]8) Color System SettingINPUT3 and INPUT4 correspond to and automatically determine

199Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]9) Signal Format SettingThis display automatically identifies PC signals and video

2Table of ContentsINTRODUCTION ... 4FEATURES ...

203.1 Installation Site RequirementsIf the site requires modifications or special preparations before installing the Plasma Display or its mounting ha

200Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]If it is not displayed correctly when “AUTO” has been set, change the setting of t

201Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]10) DVI SettingChoose the component type (either [PC] or [VIDEO]) that is connected

202Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]11) Menu Language Display SettingThe factory setting for the menu display language

203Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]STANDARD1, STANDARD2 (STANDARD)*For an overall bright video, there is no change(Fig

204Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]1 Select ‘OPTION’.2 Place the cursor over ‘ENERGY SAVE’ then press the [SET]button

205Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]–SETEXITMENUMONDAY12:00:00SAVING TIMEDAYLIGHTSET RETURNPRESENT TIME: OFF–SETEXITM

206Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]15) Orbiter SettingThis function gradually moves the display position of the scree

207Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]16) Soft Focus SettingImages are softened by suppressing the edge contrast.Factory

208Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]17) Auto Set Up Mode SettingThis function automatically adjusts the signal when th

209Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]18) Screen Position, Clock Frequency and Clock Phase AdjustmentIn AUTO SET UP, the

219) Temperature and humidity conditions • The installation site should meet the following conditions:• Operating temperatures: 0 °C to 40 °C (largely

210Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]6 Use the [2/3] buttons to adjust the click frequency.In step 4, the left side was

211Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]19) Auto Function Mode SettingWith the Auto Function mode it is possible to automat

212Menu Mode [Applicable only when a PDA-5003/PDA-5004 is installed]20) PIP DETECT SettingDuring picture-in-picture display, if no subscreen input sig

213Menu Mode[Applicable only when a PDA-5003/PDA-5004 is installed]21) SPLIT FREEZE SettingFor setting other than [OFF], the image displayed when the

214Integrator Mode5.4 Integrator Mode5.4.1 About the Integrator Mode1) Entering the Integrator Mode• It is possible to set the integrator mode by the

215Integrator Mode5.4.2 Example of Integrator Mode OperationThe basic operation in the menu mode is explained usingbrightness adjustment as an example

216Integrator Mode5.4.3 Adjustment and Setting in the Integrator ModeFor details about button controls, refer to section 5.4.2, “Example of Integrator

217Integrator Mode2) WHITE BALANCE AdjustmentThe adjustable items are R. HIGH, G. HIGH, B. HIGH, R. LOW, G. LOW and B. LOW.1 Enter the integrator mode

218Integrator Mode3) COLOR DETAIL setting1 Enter the integrator mode.(Refer to section 5.4.1, “About the Integrator Mode” (pg. 214).)2 Select ‘PICTURE

219Integrator Mode4) GAMMA SettingThis function sets the GAMMA characteristics for the video.Factory setting: GAMMA 2.21 Enter the integrator mode.(Re

22Installation Conditions3.2 Installation Conditions (PDP-507CMX)3.2.1 Heat dissipationThis unit has openings for effective ventilation. Vent location

220Integrator Mode5) SCREEN (Screen Position) AdjustmentThe adjustable items are H. POSITION, V. POSITION, CLOCK, PHASE, H. SIZE and V. SIZE.1 Enter t

221Integrator Mode6) Brightness Enhancement (BRT. ENHANCE) Setting at the Center of the ScreenThis function improves and enhances the brightness of th

222Integrator Mode1 AUDIO INPUT (INPUT1) Stereo mini jack2 AUDIO INPUT (INPUT2) Stereo mini jack3 AUDIO INPUT (INPUT3/4) ★1 (INPUT3)

223Integrator ModeINTEGRATOR INPUT1ENTERSCREEN SETUP OPTIONPROGRAM T I MERSCREEN MASKS I DE MASKV I DEO WALLBAUD RATEI D NO. SETPICTURE::

224Integrator Mode7 Viewing the program timer screen• “∗” in the DATE columnThis indicates “every”. When there is only “∗” in the DATE column, it mean

225Integrator Mode9) SCREEN MASK SettingThis function displays the inverse of the normal picture on the entire screen, or displays a single color such

226Integrator Mode10) SIDE MASK SettingThis mode is for adjusting the brightness of the no-image section around the screen when the screen size is ‘4:

227Integrator ModeSIDE MASK808080R. LEVELG. LEVELB . LEVELDEFAULTRETURN:::AUTO SIDE MASK OFF:SETEXITMENUScreen 66 Place the cursor on ‘DEFAULT’ then p

228Integrator Mode11) VIDEO WALL SettingUse this feature to configure a four panel to 25-panel video wall.NoteThis setting is adjusted when the screen

229Integrator Mode7 Setting the positionThe POSITION is where a particular panel resides in the videowall.6 Place the cursor on ‘POSITION’ then press

233.2.2 Calculating heat quantityAs a courtesy to our customers, we have included the power formula for calculating air conditioning needs.For power c

230Integrator ModeDisplay 1Display 2Display 3Display 4No.1No.2No.3No.4No.1No.2No.3No.4No.1No.2No.3No.4No.1No.2No.3No.4COMBINATIONINCOMBINATIONOUTCOMBI

231Integrator Mode(When 16 and 25 screen Video Walls)OFF → MODE1 (after approx. one second)* → MODE2 (after approx. two seconds)** The seconds shown a

232Integrator Mode12) BAUD RATE SettingIt is possible to switch the RS-232C transmission speed (baud rate) when controlling or adjusting the display u

233Integrator Mode13) Assigning an IDThis option assigns the ID necessary to adjust only the designated display in a video wall or to make an adjustme

234Integrator ModeNote• If the Remote Control does not work, display screen 2. Then press [CLEAR] button, the setting back ‘ALL’.• This function does

235Integrator Mode14) Cooling Fan Control SettingA cooling fan is located on the rear surface of the display.This function switches the method for con

236Integrator Mode15) OSD Display SettingThis option allows the On-Screen-Display (OSD) menu to appear or to be hidden. OSD menu display features andl

237Integrator Mode7 Setting the display modeIf the display is installed vertically, set the display mode to ‘V’.6 Place the cursor on ‘ANGLE’ then use

238Integrator Mode16) FRONT INDICATOR SettingThis function controls the flashing of the indicator on the front of the display.Factory setting: ON1 Ent

239Integrator Mode17) COLOR MODE SettingIn addition to the normal operation mode (NORMAL), this display has a (STUDIO) mode for use in a TV studio. Th

24Installation ConditionsThis unit is designed to be mounted using four bolt holes. For additional safety, we recommend securing it at four or sixpoin

240Integrator Mode18) PRO USE SettingFactory setting: UNDERSCAN ... OFFIMAGE PROCESS ... NORMALSIGNAL TYPE ... MOTION1 Enter the i

241Integrator ModeUNDERSCANThis function causes the outer edge of the display to appear, beyond the normal effective data area for a video signal.[Met

242Integrator ModeINTEGRATOR INPUT1CHANGESCREEN SETUP OPTIONF AN CONTROLOSDF RONT I ND I CATORCOLOR MODEPRO USEFRCPICTURE::::SETEXITMENUAUTONORMA

243Integrator Mode*1, 2: The recommended signal formats are shown below.★ Applicable only when a PDA-5003 or PDA-5004 is installed.Dot ClockH-PeriodH

244Integrator Mode20) POWER ON MODE SettingThis function sets the input at the time the power is switched on.Factory setting: INPUT ... LASTVOL

245Integrator Mode33 0 to 42LAST227 Setting when MULTI is selectedPlace the cursor on ‘MULTI MODE’ then use the [2/3] buttons to change the settings.E

246Integrator Mode21) SEAMLESS SW SettingThis setting switches between inputs at a speed of approximately 0.4 seconds.Factory setting: SEAMLESS ...

247Integrator ModeThe ‘MIRROR MODE: XY’ setting is useful when the panel is hung upside down from the ceiling. With the displaysuspended from the PDK-

248Integrator Mode4 Each time the [SET] button is pressed, the setting changesas shown below (the OSD is also reversed).The ‘MIRROR MODE’ setting is c

249Integrator Mode23) MULTISCREEN SettingThis function divides the screen into two areas when the remote control’s SPLIT button is pressed.Factory set

25Installation Conditions3.2.4 Mounting surface warpingThe display incorporates glass. Before mounting the panel using hardware other than that provid

250Integrator ModeS BY S SIZE/S BY S LAYOUTSelect a SIDE BY SIDE mode display, six options.MODE1 MODE2 MODE3NORMAL SBYS1 SBYS2 SBYS3FULL SBYS4 SBYS5 S

251Integrator ModePIP SIZESelect the size of the PICTURE IN PICTURE sub-screen.NoteIt is also reflected in the sub-screen size when PIP has been set b

252Integrator ModeTRANSLUCENT PIPSelect the degree of transparency for the PICTURE IN PICTURE sub-screen.As the translucent percentage rises, the sub-

253Integrator Mode24) REPEAT TIMER SettingWhen two input modes have been set, they are displayed alternatively.This can be used to set one screen, two

254Integrator Mode7 Setting the two screen REPEAT TIMER• MODE ... This sets the display mode.S BY S1 ⇔ S BY S2 ⇔ S BY S3 ⇔ BTM LEFT ⇔

255Integrator Mode25) FUNCTIONAL LOCKThis is the FUNCTIONAL LOCK function that prevents operation from the main unit panel or the remote control inord

256Integrator Mode26) Center Position DisplayIt is possible to display the horizontal and vertical center position.1 Press the [MUTING] button twice.2

257Integrator Mode5.4.4 PICTURE, White Balance and SCREEN Position Adjustment Values Memory Area TablesThe memory areas for the PICTURE, White Balance

258Integrator Mode7 INPUT2¥CONTRAST¥BRIGHTNESS¥H. ENHANCE !¥V. ENHANCE !¥COLOR ★¥TINT ★¥SHARPNESS ★¥H. POSITION¥V. POSITION¥COLOR TEMP. ★¥DNR ★¥MPEG N

259Integrator Mode¥CONTRAST¥BRIGHTNESS¥COLOR ¥TINT¥SHARPNESS¥H. POSITION¥V. POSITION¥COLOR TEMP. ¥DNR¥MPEG NR¥CTI¥PURECINEMAINPUT3–SIGNAL#1¥CONTRAST¥B

263.3 Installation Conditions (PDP-427CMX)3.3.1 Heat dissipationThis unit has openings for effective ventilation. Vent locations are marked by arrows

260Integrator Mode7 INPUT4¥CONTRAST¥BRIGHTNESS¥COLOR ¥TINT¥SHARPNESS¥H. POSITION¥V. POSITION¥COLOR TEMP. ¥DNR¥MPEG NR¥CTI¥PURECINEMAINPUT4–SIGNAL#1¥CO

261Integrator Mode7 INPUT5¥CONTRAST¥BRIGHTNESS¥H. ENHANCE !¥V. ENHANCE !¥COLOR ★¥TINT ★¥SHARPNESS ★¥H. POSITION¥V. POSITION¥CLOCK !¥PHASE !¥COLOR TEMP

2625.5 RS-232C AdjustmentThis display has an RS-232C terminal. It is possible to use a PC to make various adjustments and settings.5.5.1 About the RS-

263RS-232C Adjustment5.5.2 Interface1) ConnectorD-sub 9 pins (male/straight)2) Pin layout3) Baud Rate9 600 bps (standard)(switch-able to 1 200, 2 400,

264RS-232C Adjustment5.5.3 Combination ConnectionWhen controlling/adjusting panels, it is convenient to connect several displays to one PC.By performi

265RS-232C Adjustment5.5.4 ID AssignmentThe ID is assigned from the PC.Commands: <IDC> (ID CLEAR) ... Clears the assigned ID<IDS> (ID

266Under the connection conditions shown below, use a combination cable for up to 16 panels.Conditions: 1 Length of RS-232C cable connecting PC to Pla

267RS-232C Adjustment5.5.5 List of RS-232C Commands (Command 434CMX = Command 43MXE1 / Command 505CMX =Command 50MXE10 , 50MXE11 , 50MXE1 , 50MXE1-S /

268RS-232C AdjustmentCommand434CMX505CMXCommand425CMXCommand427CMX507CMXFunctionNumber directLastmemoryCommentEffective Minimum MaximumMSTS06++Sets th

269RS-232C AdjustmentCommand434CMX505CMXCommand425CMXCommand427CMX507CMXFunctionNumber directLastmemoryCommentEffective Minimum MaximumCLSS05++Sets co

273.3.2 Calculating heat quantityAs a courtesy to our customers, we have included the power formula for calculating air conditioning needs.For power c

270RS-232C Adjustment7 “INTEGRATOR”–“PICTURE” related commandsCommand434CMX505CMXCommand425CMXCommand427CMX507CMXFunctionNumber directLastmemoryCommen

271RS-232C Adjustment7 “INTEGRATOR”–“OPTION” related commandsCommand434CMX505CMXCommand425CMXCommand427CMX507CMXFunctionNumber directLastmemoryComment

272RS-232C AdjustmentCommand434CMX505CMXCommand425CMXCommand427CMX507CMXFunctionNumber directLastmemoryCommentEffective Minimum MaximumFANFCM++Maximiz

273RS-232C AdjustmentCommand434CMX505CMXCommand425CMXCommand427CMX507CMXFunctionNumber directLastmemoryCommentEffective Minimum Maximum– BPIS01+Sets t

274Command434CMX505CMXCommand425CMXCommand427CMX507CMXFunctionNumber directLastmemoryCommentEffective Minimum Maximum––RMCS26 Remote control key: POIN

2755.5.6 QUEST CommandsWhat are QUEST commands?• Quest commands output TXD such as adjustment data from the panel’s microprocessor to a PC.• Adjustmen

276RS-232C Adjustment1) Obtaining QST Status InformationSequenceData Content Size Remarks1 STX 1 Byte 02hex2 Command echo-back 3 Byte QST (fixed)3 Gen

277RS-232C Adjustment2) <QPI> Obtaining Integrator/PICTURE informationSequenceData Content Size Remarks1 STX 1 Byte 02hex2 Command echo-back 3 B

278RS-232C Adjustment5) <QSS> Obtaining SETUP informationSequenceData Content Size Remarks1 STX 1 Byte 02hex2 Command echo-back 3 Byte QSS (fixe

279RS-232C AdjustmentSequenceData Content Size Remarks27 PRO USE UNDERSCAN 1 Byte 0: OFF 1: ON28 PRO USE IMAGE PROCESS 1 Byte 1: NORMAL 2: PURE 3: MON

28[427CMX]Installation ConditionsThis unit is designed to be mounted using four bolt holes. For additional safety, we recommend securing it at four, s

280RS-232C Adjustment9) <QAP> Obtaining machine nameSequenceData Content Size Remarks1 STX 1 Byte 02hex2 Command echo-back 3 Byte QAP (fixed)3 M

2817 Table of commands not compatible with PDP-434CMX to PDP-425CMXAJN Ends 232C integrator adjustment mode.AJY Starts 232C integrator adjustment mode

282RS-232C Adjustment7 Check SumThis is data to which 2-Byte ASCII code is added to a data group returned by a QUEST command.STX02 (hex) 2 Byte 3 Byte

283Screen Burning5.6 Screen BurningWhen the same image is reproduced for a long period (still image, telop, etc.), the image is burned into to screen.

284Screen Burning7 Standard Functions (Settings cannot be changed)1 Auto Brightness Adjustment (still image detection)When an image that has little or

285Precautions on Connecting Camera Images/Concerning frame delay (lip sync)FRCsettingVideo input signalInput verticalfrequency (Hz)Frame delaynumber

286Precautions6.1 Precautions1) If the power shuts down and stays OFF for an extended time, an internal problem has probably occurred (failing part,et

287Maintenance1) Be sure to unplug the power cord from the power outlet before performing maintenance.NoteIf the plasma display is connected to a comp

288Maintenance3) Screen (front protection panel)The screen (front protection panel) is treated with a special coating to prevent glare and is very del

29[427CMX] Installation Conditions3.3.4 Mounting surface warpingThe display incorporates glass. Before mounting the panel using hardware other than th

3Table of ContentsCAUTION • To prevent injury and material damage, thoroughly readthis manual and all labels found on the equipment beforeattempting t

30Installation ProceduresRef. No. Terms3.4 Installation Procedures3.4.1 Transportation precautions• Once the shipping container is opened, transportin

31Installation ProceduresRef. No. TermsPDP-427CMXThe original packing material can be re-used to safely ship the Plasma Display. When repacking, it is

322) Unpacking procedures1 Remove the packing bands.2 Slowly lift and remove the upper carton.3 Lift and remove the carton cover.4 Remove the pads.5 R

333.4.4 Re-packing (re-packing and re-shipping are not covered by the warranty)If the unit needs to be re-packaged, observe the following guidelines.•

344) Arranging and securing cables with speed clamps and bead bandsFasten cables using the supplied speed clamps.Once speed clamps are fastened, they

35[507CMX] Special Installation (Mounting to fittings)3.5 Special Installation (PDP-507CMX)The unit can be hung from or embedded in a wall. However, s

36[507CMX]Special Installation (Mounting to fittings)35 mm orlessAttach so thatthe fan is onthe left sidewhen viewedfrom the rear.Example 1Example 3Ex

37[507CMX]3.5.2 Hanging on the wallCarefully read the following imformation before attempting to hang the unit on a wall. Take note of the various lim

38[507CMX]Special Installation (Hanging on the wall)Methods of Securing: Basic methods of securing the panel to a wall are shown below. Avoid blocking

39[507CMX] Special Installation (Embedding in the wall)AAAX (Front of the unit)<Viewed from Above><Viewed from the Right Side>✩ Operating

4IntroductionIntroductionThe contents of “5.1 Before Beginning Adjustments (pg. 144)” and subsequent sections are premised on the PDP-507CMX/PDP-427CM

40[507CMX]Special Installation (Embedding in the wall)Temperature Measurement Points (Illustration for reference purposes)• Make measurements at a dis

41[507CMX]Cation : Due to possible heat issues, we do not recommend installing the panel in narrow, enclosed areas.✩ Operating Temperature Restriction

42[507CMX]Special installation (When the display is put in a box)3.5.4 When the display is put in a boxOperating this display in confined spaces is n

43[507CMX] Special Installation (Ceiling suspension with wires)When suspending from a ceiling with wire, use the brackets shown below to prevent conce

44[507CMX]Special Installation (Ceiling suspension with wires)Methods of Securing: Basic methods of securing are shown below. Avoid blocking or coveri

45[507CMX] Special Installation (Hanging on the wall lengthwise)3.5.6 Hanging on the wall lengthwiseCarefully read the following imformation before at

46[507CMX]Special Installation (Hanging on the wall lengthwise)Methods of Securing: Basic methods of securing are shown below. Avoid blocking or cover

47[507CMX]Special Installation (Place product upright and flush, embedded in the wall)X (Front of the unit)<Viewed from Above><Viewed from th

48[507CMX]Special Installation (Place product upright and flush, embedded in the wall)Methods of Securing: Basic methods of securing are shown below.

49[507CMX]Cation : Due to possible heat issues, we do not recommend installing the panel in narrow, enclosed areas.✩ Operating Temperature Restriction

5FeaturesFeatures and Functions of this devicePDP-507CMX¶ Introduces newly developed Wide Plasma PanelThe new, wide, high-precision plasma panel (1365

50[507CMX]Special Installation (Place product upright and flush, embedded in the wall)Methods of Securing: Basic methods of securing are shown below.

51[507CMX]✩ Operating Temperature Restrictions (*1)• Ambient temperature: 0 °C to 35 °C • The same operating temperature restrictions apply to the sp

52[507CMX](2) When the Plasma Display is in a confined spaceOperating this display in confined spaces is not recommended.• If the display is to be use

53[507CMX]2 Installing three or more units (Horizontal connection)The following table lists the operating temperature conditions. Use the units under

54[507CMX]3.5.10 MultipleWhile the display is designed to accommodate side-by-side installations, keep in mind that specific installationconfiguration

55[427CMX] Special Installation (Mounting to fittings)3.6 Special Installation (PDP-427CMX)The unit can be hung from or embedded in a wall. However, s

56[427CMX]Special Installation (Mounting to fittings)35 mm orlessAttach so thatthe fan is onthe left sidewhen viewedfrom the rear.Example 1Example 2Ex

57[427CMX]3.6.2 Hanging on the wallCarefully read the following imformation before attempting to hang the unit on a wall. Take note of the various lim

58[427CMX]Special Installation (Hanging on the wall)Methods of Securing: Basic methods of securing the panel to a wall are shown below. Avoid blocking

59[427CMX] Special Installation (Embedding in the wall)AAAX (Front of the unit)<Viewed from Above><Viewed from the Right Side>✩ Operating

6Power requirements ... AC 100 V to 120 V, 50 Hz/60 Hz(The power unit range is from AC100 V to 240 V (50 Hz/60 Hz))In-rush ...

60[427CMX]Special Installation (Embedding in the wall)Temperature Measurement Points (Illustration for reference purposes)• Make measurements at a dis

61[427CMX]Cation : Due to possible heat issues, we do not recommend installing the panel in narrow, enclosed areas.✩ Operating Temperature Restriction

62[427CMX]Special installation (When the display is put in a box)3.6.4 When the display is put in a boxOperating this display in confined spaces is n

63[427CMX] Special Installation (Ceiling suspension with wires)When suspending from a ceiling with wire, use the brackets shown below to prevent conce

64[427CMX]Special Installation (Ceiling suspension with wires)Methods of Securing: Basic methods of securing are shown below. Avoid blocking or coveri

65[427CMX]610DDA93.452.552.5C10102221.625B10Avoid blocking or covering this area on the upper and lower sides.Attach so that the fan is on the left si

66[427CMX]Special Installation (Hanging on the wall lengthwise)Methods of Securing: Basic methods of securing are shown below. Avoid blocking or cover

67[427CMX]Special Installation (Place product upright and flush, embedded in the wall)X (Front of the unit)<Viewed from Above><Viewed from th

68[427CMX]Special Installation (Place product upright and flush, embedded in the wall)Methods of Securing: Basic methods of securing are shown below.

69[427CMX]Cation : Due to possible heat issues, we do not recommend installing the panel in narrow, enclosed areas.✩ Operating Temperature Restriction

7SpecificationsPDP-427CMXPower requirements ... AC 100 V to 120 V, 50 Hz/60 Hz(The power unit range is from AC100 V to 240 V (50 Hz/60 Hz))In

70[427CMX]Special Installation (Place product upright and flush, embedded in the wall)Methods of Securing: Basic methods of securing are shown below.

71[427CMX]✩ Operating Temperature Restrictions (*1)• Ambient temperature: 0 °C to 35 °C • The same operating temperature restrictions apply to the sp

72[427CMX](2) When the Plasma Display is in a confined spaceOperating this display in confined spaces is not recommended.• If the display is to be use

73[427CMX]2 Installing three or more units (Horizontal connection)The following table lists the operating temperature conditions. Use the units under

74[427CMX]3.6.10 MultipleWhile the display is designed to accommodate side-by-side installations, keep in mind that specific installationconfiguration

75[427CMX] Special installation

76How to use the standard mounting components[507CMX : 427CMX]4.1 Standard Mounting Components Features and CharacteristicsIn addition to reliability

77Handling the Standard Mounting Components4.2 Handling the Standard Mounting Components4.2.1 Handling precautionsThis section of the manual discusses

784.3 Installation of the Attachment Stand(Can be used only with the PDP-427CMX)Be sure to fix the supplied stands to the installation surface.Use com

79[427CMX]Installation of the Attachment StandDimensions(Unit: mm)23610633447.2 70102240.474.398127.7300252.431.422.110791053.524.310125011066.8ø24R12

8640x480 59.9 Hz 31.5 kHz72.8 Hz 37.9 kHz75 Hz 37.5 kHz85 Hz 43.3 kHz100.4 Hz 51.1 kHz120.4 Hz 61.3 kHz720x400 70.1 Hz 31.5 kHz NEC PC-980085.1 Hz 37.

804.4 Video Card: PDA-5003/PDA-50044.4.1 SpecificationsExternal dimensions ... PDA-5003: 301.5 mm (W) × 27.6 mm (H) × 148.9 mm (D)(11-7/

817 PDA-5004Video-relatedINPUT1 Input The following signal is supported only when a PDA-5004 is installed.• Component video signalY ...

824.4.2 External Dimensions(Unit: mm)7 PDA-5003Video Card: PDA-5003/PDA-5004148.9137.3301.527.62627 PDA-5004137.3148.327.6301.5262[507CMX : 427CMX]

83<PDP-507CMX connection panel: when equipped with PDA-5003>★: Symbol indicates the alignment point.<PDP-507CMX connection panel: when equipp

844.4.3 Installing proceduresInstallation instructions are listed below. When installingthe unit, if a screw or other object should drop inside thePla

85Video Card: PDA-5003/PDA-50044 Affix the accessory connector indicator label to thePlasma Display then affix the remote control labelto the remote c

86Video Card: PDA-5003/PDA-5004*1 Although INPUT1 and INPUT5 are compatible with variouskinds of signals, setup using the on-screen menu isnecessary a

87Video Card: PDA-5003/PDA-5004Connection to AV componentsConnection to AV component equipped withcomponent video jacksMake component video connection

88Video Card: PDA-5003/PDA-5004Connection of G ON SYNC analog RGB sourceMake G ON SYNC connections for a component withoutput that has the synchroniza

89Video Card: PDA-5003/PDA-5004Connection to a personalcomputerConnection method differs depending on the computertype. When connecting, please thorou

92.2 External DimensionsPDP-507CMXWEIGHT: 35.5 kg (78.3 lbs) (without stand)MATERIAL: Front: Resin; Rear cover: Metal plate, Front protector panel: Gl

90Video Card: PDA-5003/PDA-5004When connecting to ANALOG RGB IN (INPUT1)ANALOG RGB OUT(D-Sub)ANALOG RGB IN(D-Sub)INPUT1Connect the cable corresponding

91Video Card: PDA-5003/PDA-5004When connecting to COMPONENT VIDEO (INPUT5)[Connections for PDA-5004]Y Pb/Cb Pr/CrINPUT5COMPONENTVIDEOOn-screen setup i

92Video Card: PDA-5003/PDA-50044.4.7 Connection to INPUT2A computer equipped with DVI output (digital RGB signal)or an AV component equipped with DVI

93Video Card: PDA-5003/PDA-50044.4.10 About DTV set top box connectionTo ensure proper connection, please carefully read theinstruction manual supplie

94Video Card: PDA-5003/PDA-50044.4.11 Audio connectionsBefore making connections, be sure to check that theaudio component’s power and the display’s m

95Video Card: PDA-5003/PDA-5004[When using PDA-5004]Audio connection for component connected toINPUT3RLINPUT3AUDIOThe audio line for the component con

96Video Card: PDA-5003/PDA-5004Signal Format50ComponentRGBComponentRGBComponentRGBComponentRGBComponentRGBComponentRGBComponentRGBComponentRGBComponen

97Video Card: PDA-5003/PDA-5004INPUT 27 Video signals supported ★ (applies only whenequipped with PDA-5003/PDA-5004)INPUT 3★(applies only when equippe

984.5.2 Installation coordinates for screws used to attach the stand to a surface* When stabilizing the stand to a surface, use M6 longer than 20 mm.U

99Table Top Stand: PDK-TS074.5.3 External Dimensions7 When using Plasma Display PDP-507CMXUnit: mm (inch)1222 (48-1/8)785 (30-29/32)267(10-1/2)508 (20