Pioneer RM-V4000V Manuel d'utilisateur

1RNotes:• Pioneer will not be liable for any loss caused by defectsof the parts supplied other than by Pioneer.• An damage during shipping will be com

9TypeBNC connectorBNC connectorBNC connectorBNC connectorBNC connectorSlide switchTact switchTact switchTact switchTact switchTact switchTact switchD-

13148845(148)(1031)(769)630GENERAL SPECIFICATIONS(2) Projection Screen Kit (RMS-V4011/V5011) Product Weight : 11.0 kg/14.0kg(Fig.2-2)Unit:mmThe number

14630(769)845(1031)GENERAL SPECIFICATIONS(3) Projection Frame (RMF-V4011/V5011) Product Weight : 26.8kg/28.8kg1201(1352)(Fig.2-3)Unit:mmThe number in

1800299154303141916420GENERAL SPECIFICATIONSRear ViewSide ViewFront View(7) Multi Video Processor (RMD-V3216/V3109, RMD-V2170)1 Multi Video Processor

PIONEER RM-V4000 / 5000MANUAL.This Acrobat (IE: a PDF file) version of the Pioneer RM-V4000 / 5000 manual was made fromthe original digital document a

19GENERAL SPECIFICATIONS(Fig.2-8)Front ViewSide ViewRear ViewMain Specifications of Multi Video Processor (RMD-V2170)Input video signal ...

20POWERINPUT SELDISP CALLMAIN MENUADJ OUT013579ABCDEFRGBADJ ADJ ADJON/OFF ON/OFF ON/OFF2//3–+4682ADJ INDÎADJUSTMENT CONTROL UNIT

21GENERAL SPECIFICATIONS(8) Projection Cabinet (RMF-V4011R) AccessoriesTo attach the multi-projection unit (RM-V4000V) to the conventional RM-V2000A,

25(1) Installing Ground1 GroundThe ground must be flat and horizontal. It should be able to bear the weight of the system.For wooden floors, if the p

2CHAPTER 1. FEATURES OF PROJECTION CUBE SYSTEM ... 41. FEATURES OF SYSTEM ...

31(11) Lighting• The projection screen kit (RMS-V4011/V5011) will not reflect like TV screens when exposed to external light, but may reflectif direct

342. INSTALLATION AND ASSEMBLY(1) Confirmation1 Decide the position for installing the system according to the installation conditions in Chapter 3.Ch

353 Multi Projection Unit (RM-V4000V/V5000V)[1] Open the upper carton, and remove the ABL cable and instruction manual provided.[2] Remove the upper c

364 Projection Screen Kit (RMS-V4011/V5011)* Projection screen kit is double-packaged to maintain its performance. After removing the middle cover p

375 Projection Frame (RMF-V4011/V5011)[1] Open the upper carton and cut the PP bands (eight) securing the internal parts.[2] Remove the two horizontal

38(Fig. 3-10)INSTALLATION AND ASSEMBLY6 Projection Cabinet (RMF-V4011R)[1] Open the upper carton and remove packings B and C, and the instruction manu

39(3) Carrying the Units After Opening PackagingTo carry the screen unit and multi-projection unit after opening the packaging, hold them by the parts

41(Fig. 3-13)H-shape frame assembly (L)4 Rivet5 Shield2 H-shape frame assembly (L)1 Screw (M5 × 35)1 StopperTable1 Base assemblyB-5 Guide fixtureA-5

42(2) Assembling the SystemThe basic procedure for assembling the system is as follows.1 Assemble the projection stand (RM-V112/RMA-V5010).2 Mount a o

444 Multi Projection Unit (RM-V4000V/V5000V)The Multi-Projection Unit is designed to be mounted from the back of the cabinet normally. If sufficient s

45b When mounting from the front[1] Remove the two stoppers and two metal fixtures from the cabinet. (Fig. 3-23)[2] Pull the table to the front.[3] In

465 Projection Screen Kit (RMS-V4011/V5011)[1] Mount the screen unit serving as the reference. Basically, mount from the center unit at the bottom.a I

47[2] Join the next screen beside the screen mounted as the reference and mount the remaining screens in order. (Stack themfrom the bottom to the top.

486 Top panel, Side panel, Rear panelAs this system is of the rear projection type, it must be enclosed to avoid exposure to external light. (Fig.3-2

503' Attaching the Multi Projection Unit (RM-V4000V) to the Projection Cabinet (RMF-V4011R)The figure shows the assembling procedure of the left

51(5) Paste spacer A (BMR1073) to the top board of themulti-projection unit and spacers B (BMR1074) to thetwo sides at the position shown in the fig

52(10) Attach the adjuster (BEF1011) attached with a nut(M8) to the rear holders R and L (BNG1205 and 1206).(12) Attach each rear panel (BMR1069, 1070

53INSTALLATION AND ASSEMBLYScreen5. SPECIAL INSTALLATION(1) Wall inset• If removing the screen after installing the system, the person must go behind

541. ADJUSTMENT PREPARATIONS(1) Wiring1 Connection of Power Supply• The power supply can be connected to up to 3 units in a series using the AC outlet

57When TV SYSTEM=AUTO<VIDEO, Y/C Input)• Selects the convergence memory from MEMORY-1 or MEMORY-2 automatically according to the signals input (NTS

58(3) White Balance Adjustment MemoryADJUSTMENTS has altogether six white balance adjustment memories.VIDEO, Y/C input memoryRGB input memoryFactory s

59(6) Giving IDsWhen several Multi projection units are used to compose the 9 screens or 16 screens (multi-screen), the ID is used to differen-tiate b

60<Giving IDs Using the Remote Control>[1] Enter the adjustment mode.[2] The main menu will be displayed. Press the 1 key.Select ”1. ID CLEAR/SE

61SourceExpandedNTSCIndividualY/CRGBCubeInput Function) By switching Y/C↔RGB, switchesexpansion/individual (video distortion is great)TV SYSTEM) Compo

62ADJUSTMENTS(3) When Switching Source Inputs to Multi Video Processor (1)-When using Pioneer's new Multi Video ProcessorInput Function) RGBTV SY

63ADJUSTMENTS(5) When Using Two Multi Video Processors without Frame Adjusting FunctionRGBCubeMulti VideoProcessor 1Multi VideoProcessor 2ExpandedNTSC

64(7) When Switching the Source Input to the Multi Video ProcessorInput Function: RGBTV SYSTEM: AUTOConverter data required for playing: ThreeFor exam

65ADJUSTMENTS4. SCREEN ADJUSTMENTS(1) Adjustment FlowchartThe following shows the order for performing the adjustments generally required in the setup

67ADJUSTMENTSThe & numbers correspond to the numbers in the flow-chart.2 Adjustment signal inputFor adjusting size...Monoscope, etc.(EX.LD Test di

68V PHASE(V STATIC whenMULTI ON)3,4,7 center adjustmentSet to only green and adjust the center with V PHASEH PHASE .When MULTI ON, as V PHASE do

69ADJUSTMENTSCurrent is also supplied to the vertical deflection york withV STATIC . If supplied excessively, distortion will occur asshown in the rig

70Explanation of H BLK L and H BLK R Adjustments H BLK L and H BLK R adjustments are performed to obtain the optimum convergence adjustment wav

71ADJUSTMENTS5 H BLK R AdjustmentOutput all three colors R,G,B, observe the right side of the screen , and adjust with H BLK R sothat the color st

72ADJUSTMENTSNo color deviationSudden distortionColor deviationNo distortion NOTEWhen H BLK R is adjusted so that the three colorsR,G,B do not

73Observehere6 H BLK L adjustmentOutput all three colors R,G,B, observe the left side of the screen , and adjust with H BLK L so thatthe color st

74ADJUSTMENTS9 V SIZE adjustmentSet to only green, observe the top part of the screen , andadjust the data amount in the vertical direction using

76ADJUSTMENTSMovement of screen by point convergence adjustmentMovement of screenOSD displayUse especially when adjusting the horizontal size of the

77In adjustment step q , observe the external part of the screen, adjust the 16 adjusting points there, taking note of linearity inthe peripheral ar

78ADJUSTMENTSMovement on screenDisplayed OSD

7DimensionsGENERAL SPECIFICATIONS(Fig.2-1)

79ADJUSTMENTS

80ADJUSTMENTS

81ADJUSTMENTS

82ADJUSTMENTS

835 24 16 3ADJUSTMENTS NOTEIf only one point is moved greatly in the point conver-gence mode, it may not move in areas smaller than thedesired adj