Pioneer PRV LX1 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Joueurs Pioneer PRV LX1. Pioneer PRV LX1 User Manual [fr] Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Preparation for Updating
Preparation for Updating
STEP1
* Executing the updating causes the DVD background image files previously imported by
the user to be deleted. These files need to be imported again after completion of
updating.
Other user's data and settings (recorded video clips and various setups) are held
unchanged in the system.
* Be very careful against unexpected power failure during updating, for the unit may
become unable to be started normally after it has been turned off in the middle of
updating.
Should the unit fails to start normally due to unexpected power failure, try upgrading
the system again as described in this document. If the unit is still unable to start
normally, please contact our Technical Support Center.
STEP1
Turning the Unit On and Entering the Update Mode
STEP2
Connect the video output of the unit to the
video input of the monitor so that the
monitor can display the played video.
Plug the power cord of the unit to a wall
power outlet.
Make sure that main power of the unit is
set to off.
* If the unit is on, be sure to turn it off.
* The unit is off when the Power indicator on the
front panel is extinguished.
Prepare the Update Disc.
Set the Main Power switch on the rear
panel to ON to put the unit in Standby
mode.
* Make sure that the Power indicator on the front
panel lights up in orange.
While holding the ENTER button on the
front panel, press the STANDBY/ON button
to turn the unit on.
The Power indicator should light up in
green and the system should start up.
When the display panels shows "PLEASE
WAIT", release the ENTER button.
* Hold the ENTER button until "PLEASE WAIT" is
shown on a display panel.
Place the Update Disc on the disc table.
Press and hold the ENTER button on the
front panel for 2 to 3 seconds.
The disc table closes and automatically
starts to read the updating program.
*Hold the ENTER button until the disc table closes.
When the display panel shows "DOWNLOAD
FULL", updating of the system begins.
During operation of the updating program,
the monitor screen shows the messages as
shown on the right.
(The lower two lines enable monitoring of
the step being executed and progress
status.)
Updating completes in about 10 minutes.
When updating completes, the monitor
screen display returns to the same display
as the display at the moment of startup of
the unit and the Update Disc is ejected
automatically.
After the above, the display panel of the
unit shows "DOWNLOAD COMPLETED",
the unit turns off automatically and it
enters the standby mode.
* It takes are few seconds before the unit shuts
down mode automatically. Do not switch off
the power supply in this period.
* The unit enters the standby mode in the
condition it has ejected the Update Disc, but
this is not a malfunction.
Take out the Update Disc, restart the unit,
and then close the disc table manually.
During startup, the display panel should
show "PLEASE WAIT" and then "POWER-
ON".
Finally, when "PGM-INSTALL" is displayed,
the disc tray opens automatically and the
update mode is exited.
The monitor screen shows the messages as
shown.
STEP2
Upgrading the System
STEP3
STEP3
Continue
------------------------------
- PRV-LX1 Program Installer -
------------------------------
PLEASE INSERT INSTALLATION CD IN DRIVE ONE,
THEN PRESS [ENTER] BUTTON ON FRONT PANEL
FOR 2 SECONDS TO BEGIN UPDATE.
>>
==============================
= PRV-LX1 Program Installer =
==============================
Setup Directories ...
Start Program Download ...
= Setup Drives. =
====
ENTER Button
While holding ENTER button,
press STANDBY/ON button.
ENTER ButtonDisplay Panels
STANDBY/ON Button
Front Panel Power Indicator
Monitor Screen Display During Updating
Update Disc
Initial Display on Monitor Screen
Disc Table
UPDATING PROCEDURE
UPDATING PROCEDURE
Before Updating
Before Updating
Turning the Unit On and Entering the Update Mode
Upgrading the System
Vue de la page 0
1 2

Résumé du contenu

Page 1 - UPDATING PROCEDURE

Preparation for UpdatingPreparation for UpdatingSTEP1* Executing the updating causes the DVD background image files previously imported by the user to

Page 2 - Details of Updating

PRV-LX1 SYSTEM UPDATING GUIDEThank you for purchasing our PRV-LX1 DVD recorder. We herein send you the PRV-LX1 System Updating Guide together with the

Commentaires sur ces manuels

Pas de commentaire