Pioneer DJM-400 Manuel d'utilisateur Page 8
- Page / 76
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
8
<DRB1404>
En
MIXER OPERATIONS (BASIC OPERATIONS)
MIXER OPERATIONS
BASIC OPERATIONS
MIC
HEADPHONES
MASTER
BEAT EFFECTS
2
7
1
3
4
5
6
TRIM
POWER
MASTER
LEVEL
HI, MID,
LOW
1. Set rear panel POWER switch to ON.
2. Set the input selector switch for the desired channel to
choose the connected component.
¶ The function of the PHONO/LINE input connectors is set using
the PHONO/LINE switch on the connection panel.
3. Use the TRIM dial to adjust the input level.
4. Use the channel equalizer dials (HI, MID, LOW) to adjust
the tone.
5. Use the channel fader lever to adjust the sound volume of
the selected channel.
6.
To use the cross fader on the selected channel, set the cross
fader selector switch to either the middle position (
) or
the right position (
), then operate the cross fader lever.
¶ When not using the cross fader, set the cross fader selector
switch to [THRU].
7. Use the MASTER LEVEL dial to adjust the overall sound
volume.
[Selecting Stereo or Monaural]
When the connection panel’s STEREO/MONO switch is set to
[MONO], the master output becomes a monaural combination of L+R
channels.
[Microphone Input]
1. Set the connection panel’s MIC/AUX switch to [MIC].
2. Set the MIC switch to [ON] or [TALK OVER].
¶ When the switch is set to [TALK OVER], if sounds of over –15
dB are detected by the microphone, the output for all sound
sources other than the microphone is attenuated by 20 dB.
3. Use the MIC 1 LEVEL dial to adjust the sound volume of
MIC 1, and the MIC 2 LEVEL dial to adjust the sound
volume of MIC 2.
4. Use the microphone equalizer dial (EQ) to adjust the tone
of the microphone sound.
¶ The microphone equalizer function operates simultaneously
on microphones 1 and 2.
MIC
HEADPHONES
MASTER
BEAT EFFECTS
2
1
3
1
4
EQ
2
LEVEL
THRU/ /
MIC 1 LEVEL,
MIC 2 LEVEL
STEREO/MONOMIC/AUX
CH-1, CH-2,
MASTER
[PHONES]
[MIC]
[AUX]
(Cross fader selector switch)
[Auxiliary Input]
1. Set the connection panel’s MIC/AUX switch to [AUX].
¶ The MIC1 input connector functions as AUX(L) input, and the
MIC2 input connector functions as AUX(R) input.
2. Set the MIC switch to [ON] or [TALK OVER].
¶ When the switch is set to [TALK OVER], if a sound is input to
the AUX connectors, the output for all sources other than the
AUX input is attenuated by 20 dB.
3. Use the MIC 1 LEVEL dial to adjust the sound from the L
channel, and MIC 2 LEVEL dial to adjust the sound from
the R channel.
4.
Use the microphone equalizer dial (EQ) to adjust sound tone.
[Headphones Output]
1. Use the headphones cue button (CH-1, CH-2, MASTER) to
select the source to be output to the headphones.
¶ The selected source button lights brightly.
[Relationship of headphones cue button and headphones output]
2. Use the LEVEL dial to adjust the headphones sound level.
[Selecting the Cross Fader Curve]
The sound volume response to fader lever operation can be set to
one of two characteristic curves.
7 Use the cross fader selector switch to select the desired
cross fader response curve.
¶ At the center position ( ), the curve operates to produce an
even, neutral rise throughout the cross fader’s movement.
¶ At the right position ( ), the curve operates to produce a rapid
rise with the cross fader’s movement (sound from [2 >] is
produced as soon as the lever leaves side [< 1]).
¶ The curve settings operate the same on both sides [< 1] and
[2 >].
Headphone cue button Headphones Output
CH-1 CH-2 MASTER L channel R channel
ON OFF OFF CH-1(L) CH-1(R)
OFF ON OFF CH-2(L) CH-2(R)
OFF OFF ON MASTER(L) MASTER(R)
ON ON OFF CH-1(L)+CH-2(L) CH-1(R)+CH-2(R)
ON OFF ON CH-1(MONO) MASTER(MONO)
OFF ON ON CH-2(MONO) MASTER(MONO)
ON ON ON
CH-1(MONO)+CH-2(MONO)
MASTER(MONO)
- CAUTIONS REGARDING HANDLING 2
- CONTENTS 3
- FEATURES 3
- SPECIFICATIONS 3
- CONNECTIONS 4
- CONNECTING INPUTS 5
- CONNECTING OUTPUTS 5
- CONNECTING THE POWER CORD 5
- BASIC OPERATIONS 8
- EFFECT FUNCTIONS 10
- PRODUCING BEAT EFFECTS 11
- IN-LOOP SAMPLER 11
- 8. IN-LOOP SAMPLER 12
- TROUBLESHOOTING 13
- IMPORTANT 14
- TABLE DES MATIÈRES 15
- CARACTÉRISTIQUES 15
- FICHE TECHNIQUE 15
- BRANCHEMENTS 16
- BRANCHEMENT DES ENTRÉES 17
- BRANCHEMENTS DE SORTIE 17
- HEADPHONES 18
- Français 19
- DÉMARCHES DE BASE 20
- FONCTION DE DÉPART EN FONDU 21
- FONCTIONS DES EFFETS 22
- BPM manuelle] 23
- GUIDE DE DÉPANNAGE 25
- Aufstellung 26
- Reinigen des Gerätes 26
- INHALTSVERZEICHNIS 27
- MERKMALE 27
- TECHNISCHE DATEN 27
- ANSCHLÜSSE 28
- LRLRLRLR 29
- Master-Ausgang 30
- Kopfhörer 30
- Frontplatte 30
- <DRB1404> 32
- FADER-STARTFUNKTION 34
- EFFEKTFUNKTIONEN 35
- Eingabe des BPM-Wertes] 36
- 8. IN- LOOP SAMPLER 37
- Beispiel 37
- EFFEKTPARAMETER 38
- STÖRUNGSBESEITIGUNG 39
- AVVERTENZE PER L’USO 40
- CARATTERISTICHE 41
- CARATTERISTICHE TECNICHE 41
- COLLEGAMENTI 42
- COLLEGAMENTO DEGLI INGRESSI 43
- COLLEGAMENTI DI USCITA 43
- COLLEGAMENTO DEL CAVO DI 43
- ALIMENTAZIONE 43
- Italiano 45
- OPERAZIONI DI BASE 46
- BEAT EFFECTS 47
- FUNZIONI DI EFFETTO 48
- CAMPIONATORE DI CICLI 49
- DIAGNOSTICA 51
- BELANGRIJK 52
- INHOUDSOPGAVE 53
- KENMERKEN 53
- TECHNISCHE GEGEVENS 53
- AANSLUITINGEN 54
- AANSLUITEN VAN APPARATUUR 55
- OP DE INGANGEN 55
- OP DE UITGANGEN 55
- AANSLUITEN VAN HET NETSNOER 55
- Nederlands 57
- BASISBEDIENING 58
- FADERSTARTFUNCTIE 59
- EFFECTFUNCTIES 60
- BEAT-EFFECTEN PRODUCEREN 61
- Voorbeeld 62
- VERHELPEN VAN STORINGEN 63
- IMPORTANTE 64
- CARACTERÍSTICAS 65
- ESPECIFICACIONES 65
- CONEXIONES 66
- CONEXIONES DE LAS ENTRADAS 67
- CONEXIONES DE SALIDA 67
- OPERACIONES BÁSICAS 70
- FUNCIÓN DE INICIO CON FUNDIDO 71
- FUNCIONES DE LOS EFECTOS 72
- BEAT/PITCH] 73
- SOLUCIÓN DE PROBLEMAS 75
- All rights reserved 76
Produits connexes et manuels pour Instruments de musique Pioneer DJM-400
(128 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.535 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels