Pioneer DJM-400 Manuel d'utilisateur télécharger pdf (Page 12)

EFFECT FUNCTIONS (IN-LOOP SAMPLER/EFFECT PARAMETERS)

4. Set the ON/OFF button to ON.

5. At the point you wish to sample record, press one of the

non-lighted BEAT/BANK buttons.

Lighted BEAT/BANK buttons have already been recorded, and

cannot be used again unless their recorded contents are erased.

¶ Recording begins automatically when the sound signal from

CD player or other component is detected. During recording,

the

BEAT/BANK

button will flash quickly. During recording

standby, the button will flash slowly at intervals.

¶ When 4 beats of sound at the measured BPM have been

recorded, the BEAT/BANK button flashes slowly and loop play

is performed.

6. If the beat becomes unsynchronized, press one of the

BEAT/PITCH buttons (–, +) to resynchronize the timing of

the playback sample to the currently playing track.

¶ The playback speed increases while the [+] button is

depressed, and decreases while the [–] button is depressed.

7. Rotate the LEVEL/DEPTH dial to adjust the sound balance

between source and sample.

8. To stop loop playback, press the corresponding

BEAT/

BANK

button.

¶ The

BEAT/BANK

button indicator will change from slow

flashing to steadily lighted.

[To Playback a Recorded Sample]

1 Set the effect selector switch to [IN-LOOP SAMPLER].

2 Use the effect channel selector to choose the channel for

loop playback.

3 Set the ON/OFF button to ON.

4 Press the BEAT/BANK button containing the sample you

wish to play as a loop.

¶ The BEAT/BANK buttons with recorded samples are lighted.

¶ The selected button will flash slowly and loop play will begin.

5 If the beat becomes unsynchronized, press one of the

BEAT/PITCH buttons (–, +) to resynchronize the timing of

the playback sample to the currently playing track.

¶ The playback speed increases while the [+] button is

depressed, and decreases while the [–] button is depressed.

6 Rotate the LEVEL/DEPTH dial to adjust the sound balance

between source and sample.

7 To stop loop playback, press the corresponding

BEAT/

BANK

button.

¶ The

BEAT/BANK

button indicator will light steadily.

[Erasing a Recorded Sample]

1 Set the effect selector to [IN-LOOP SAMPLER].

2 While holding the ERASE (BEAT/PITCH –) button

depressed, press the

BEAT/BANK

button containing the

sample you wish to erase.

The BEAT/BANK buttons containing recorded samples are lighted.

¶ The indicator in the selected BEAT/BANK button will go out

and the sample will be erased.

EFFECT PARAMETERS

Name

1 DELAY

2 ECHO

3 FILTER

4 FLANGER

5 PHASER

6 ROBOT

7 ROLL

IN-LOOP SAMPLER

BEAT/BANK button parameters

Sets delay time of 1/2 to 4/1 per 1

beat of BPM time.

Sets delay time of 1/2 to 4/1 per 1

beat of BPM time.

Cycle of cutoff frequency shift is set

in unit of 1/1 to 16/1 relative to 1

beat of BPM.

Cycle of flanger shift is set in units

of 1/1 to 16/1 relative to 1 beat of

BPM.

Cycle of phaser effect shift is set in

units of 1/1 to 16/1 relative to 1 beat

of BPM.

Robot sound effects can be set in 7

fixed values from –100 % to +100 %.

Sets effect time of 1/2 to 4/1 per 1

beat of BPM time.

Selects bank for recording/playback

of 4 beat source.

Contents

Sets delay time.

Sets cycle for

cutoff time shift.

Sets cycle for

flanger effect

shift.

Sets cycle for

phase effect shift.

Set robot sound

effect.

Sets effect time.

Setting Range (unit)

1 to 8 000 (ms)

10 to 32 000 (ms)

–100, –66, –50, 0,

+26, +50, +100 (%)

(fixed values)

10 to 8 000 (ms)

Parameter 2

(LEVEL/DEPTH dial)

Sets balance between original and

delay sound.

Sets balance between original

sound and echo sound.

Amount of effect increases when

dial is turned clockwise.

Amount of effect increases when

dial is turned clockwise. When dial

is turned fully counterclockwise,

only original sound is output.

Amount of effect increases when

dial is turned clockwise. When dial

is turned fully counterclockwise,

only original sound is output.

Amount of effect increases when

dial is turned clockwise.

Sets balance of original sound and

ROLL sound. No change is produced

when dial is turned toward the right

side of the center position.

Sets balance of original sound and

recorded sample. No change is

produced when dial is turned

toward the right side of the center

position.

Parameter 1 (BEAT button)

8. IN-LOOP SAMPLER

This function allows you to store 4-beat sounds in up to 5

banks, then output them repeatedly.

Example

Repeat

Bank 1

Present

track

BPM=125

Bank 1 ON

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 75 76

Commentaires sur ces manuels

Pas de commentaire

Pioneer DJM-400 Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Pioneer DJM-400