Pioneer DEH-2020MP Manuel d'utilisateur télécharger pdf

MANUEL D’INSTALLATION

INSTALLATION MANUAL

DEH-2020MP

DEH-2000MPB

DEH-2000MP

DEH-1020E

DEH-1000E

<YRD5142-A/S> 1

Printed in China

Imprimé en Chine

<YRD5142-A/S>

<YRD5142-A/S> 1

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts. Use of un-

authorized parts may cause malfunctions.

! Consult your dealer if installation requires dril-

ling of holes or other modifications to the vehi-

cle.

! Do not install this unit where :

— it may interfere with operation of the vehi-

cle.

— it may cause injur y to a passenger as a re-

sult of a sudden stop.

! The semiconductor laser will be damaged if it

overheats. Install this unit away from hot

places such as near the heater outlet.

! Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

60°

DIN front/rear mount

This unit can be properly installed either from

“Front” (conventional DIN front-mount) or

“Rear” (DIN rear-mount installation, utilizing

threaded screw holes at the sides of unit chas-

sis). For details, refer to the following installa-

tion methods.

DIN Front-mount

Installation with the rubber bush

1 Insert the mounting sleeve into the

dashboard.

When installing in a shallow space, use a sup-

plied mounting sleeve. If there is enough

space behind the unit, use factory supplied

mounting sleeve.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°)

into place.

3 Install the unit.

Dashboard Rubber bush

Mounting sleeve Screw

Removing the unit

1 Extend top and bottom of the trim ring

outwards to remove the trim ring. (When

reattaching the trim ring, point the side

with a groove downwards and attach it.)

Trim ring

! It becomes easy to remove the trim ring if

the front panel is released.

2 Insert the supplied extraction keys into

both sides of the unit until they click into

place.

3 Pull the unit out of the dashboard.

<YRD5142-A/S>3

Installation

<YRD5142-A/S> 2

DIN Rear-mount

1 Extend top and bottom of the trim ring

outwards to remove the trim ring. (When

reattaching the trim ring, point the side

with a groove downwards and attach it.)

Trim ring

! It becomes easy to remove the trim ring if

the front panel is released.

2 Determine the appropriate position

where the holes on the bracket and the

side of the unit match.

3 Tighten two screws on each side.

Screw

Mounting bracket Dashboard or console

! Use either truss screws (5 mm × 8 mm) or

flush surface screws (5 mm × 9 mm), de-

pending on the shape of screw holes in the

bracket.

Fastening the front panel

If you do not plan to detach the front panel,

the front panel can be fastened with supplied

screw.

Screw

<YRD5142-A/S>4

Installation

<YRD5142-A/S> 3

<YRD5142-A/S>34

<YRD5142-A/S> 4

<YRD5142-A/S> 1

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - INSTALLATION MANUAL

MANUEL D’INSTALLATIONINSTALLATION MANUALDEH-2020MPDEH-2000MPBDEH-2000MPDEH-1020EDEH-1000E<YRD5142-A/S> 1<KMMZX> <07G00000>Printed

Page 2 - DIN-Rückmontage

Importante! Compruebe todas las conexiones y sistemasantes de la instalación final.! No utilice piezas no autorizadas. El uso de pie-zas no autorizada

Page 3 - Montaggio DIN anteriore

Important! Vérifiez toutes les connexions et tous les systè-mes avant l’installation finale.! N’utilisez pas de pièces détachées non autori-sées. L’ut

Page 4 - Переднее крепление

Belangrijk! Controleer alle aansluitingen en systemenvoordat u de installatie voltooit.! Gebruik geen onderdelen van andere fabrikan-ten. Onderdelen v

Page 5 - Connection Diagram (Fig. 1)

1*2*3*4*5*1 This product2 Antenna jack3 Fuse (10 A)4 Note:Depending on the kind of vehicle, the function of 3* and 5* may be different. In this case,

Page 6 - <YRD5142-A/S>17

Importante! Cuando esta unidad se instala en un vehículosin posición ACC (accesorio) en la llave de en-cendido, el cable rojo se debe conectar al ter-

Page 7 - <YRD5142-A/S>25

Important! Quand cet appareil est installé dans un véhi-cule sans position ACC (accessoire) sur lecontact d’allumage, le câble rouge doit êtreconnecté

Page 8 - <YRD5142-A/S>33

Belangrijk! Als dit toestel wordt geïnstalleerd in een voer-tuig met een contactschakelaar zonder ACC-stand (accessoirestand), moet de rode kabelworde