Pioneer DEH-P4770MP Manuel d'utilisateur télécharger pdf

60°

182

DEH-P4770MP

Fig. 4

¥ qJA«

Note:

• Before making a final installation of the unit,

temporarily connect the wiring to confirm that

the connections are correct and the system works

properly.

• Use only the parts included with the unit to

ensure proper installation. The use of unautho-

rized parts can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifica-

tions of the vehicle.

• Install the unit where it does not get in the dri-

ver’s way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot

— for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.

(Fig. 1)

• When installing, to ensure proper heat dispersal

when using this unit, make sure you leave ample

space behind the rear panel and wrap any loose

cables so they are not blocking the vents.

DIN Front/Rear-mount

This unit can be properly installed either from

“Front” (conventional DIN Front-mount) or

“Rear” (DIN Rear-mount installation, utilizing

threaded screw holes at the sides of unit chassis).

For details, refer to the following illustrated

installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 2)

1. Dashboard

2. Holder

After inserting the holder into the dashboard,

then select the appropriate tabs according to the

thickness of the dashboard material and bend

them.

(Install as firmly as possible using the top and

bottom tabs. To secure, bend the tabs 90

degrees.)

3. Rubber bush

4. Screw

Removing the Unit (Fig. 3) (Fig. 4)

5. Frame

To remove the frame, extend top and bottom of

the frame outwards in order to unlock it. (When

reattaching the frame, point the side with a

groove downwards and attach it.)

• It becomes easy to remove the frame if the

front panel is released.

6. Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into place.

Keeping the keys pressed against the sides of the

unit, pull the unit out.

DIN Rear-mount

Installation using the screw holes on

the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)

1. Remove the frame.

7. Frame

To remove the frame, extend top and bottom of

the frame outwards in order to unlock it. (When

reattaching the frame, point the side with a

groove downwards and attach it.)

• It becomes easy to remove the frame if the

front panel is released.

2. Fastening the unit to the factory

radio mounting bracket.

8. Select a position where the screw holes of the

bracket and the screw holes of the head unit

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either truss

screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw

holes in the bracket.

9. Screw

10. Factory radio mounting bracket

11. Dashboard or Console

Installation <ENGLISH>

Fig. 2

≤ qJA«

Fig. 1

± qJA«

Fig. 3

≥ qJA«

Fig. 5

µ qJA«

Fig. 6

∂ qJA«

Fig. 7

∑ qJA«

INSTALLATION MANUAL

This product conforms to new cord colors.

Los colores de los cables de este producto se

conforman con un nuevo código de colores.

As cores dos fios deste produto seguem um novo

padrão de cores.

Printed in Thailand

<CRD3952-A/N> CS <KNNZX> <04J00000>

1 2 3 4

Résumé du contenu

Page 1 - INSTALLATION MANUAL

60°6182531234DEH-P4770MP5Fig. 4¥ qJA«8911107Note:• Before making a final installation of the unit,temporarily connect the wiring to confirm thatthe c

Page 2 - Instalación <ESPAÑOL>

Nota:• Antes de realizar a instalação final do aparelho,conecte os fios temporariamente para confirmarque as conexões estejam corretas e que o sistema

Page 3 - <ENGLISH>

13. Blue/whiteTo system control terminal of the power ampor Auto-antenna relay control terminal (max.300 mA12 V DC).11. Connecting cords with RCA pin

Page 4 - <ESPAÑOL>

Nota:• Este aparelho foi concebido para veículos com umabateria de 12 Volts e conexão à terra negativa. Antesde instalar o aparelho num veículo recrea