Pioneer Premier PRS-D4000F Manuel d'utilisateur télécharger pdf

Setting the Unit <ENGLISH>

Thank you for purchasing this PIONEER

product. Before attempting operation, be

sure to read this manual.

In case of trouble

When the unit does not operate properly,

contact your dealer or the nearest autho-

rized PIONEER Service Station.

CAUTION

Never replace the fuse with one of greater

value or rating than the original fuse. Use

of an improper fuse could result in over-

heating and smoke and could cause dam-

age to the product and injury including

burns.

CAUTION

Do NOT install or use your Pioneer ampli-

fier by wiring speakers rated at 4 Ohm (or

lower) in parallel to achieve a 2 Ohm (or

lower) bridged mode (Diagram B).

Amplifier damage, smoke, and overheating

could result from improper bridging. The

amplifier surface could also become hot to

the touch and minor burns could result.

To properly install or use a bridged mode

for a two-channel amplifier and achieve a 4

Ω load, wire two 8 Ω speakers in parallel

with Left + and Right – (Diagram A) or use

a single 4 Ω speaker. For a four-channel

amplifier, follow the speaker output con-

nection diagram for bridging as shown on

the back of your amplifier, and wire two 8

Ω speakers in parallel to achieve a 4 Ω load

or use a single 4 Ω speaker per channel.

If you have any questions or concerns,

please contact your local authorized

Pioneer dealer or call Pioneer customer

service.

WARNING

• Always use the special red battery and ground

wire [RD-223], which is sold separately. Connect

the battery wire directly to the car battery positive

terminal (+) and the ground wire to the car body.

• Do not touch the amplifier with wet hands.

Otherwise you may get an electric shock. Also, do

not touch the amplifier when it is wet.

• For traffic safety and to maintain safe driving

conditions, keep the volume low enough so that

you can still hear normal traffic sound.

• Check the connections of the power supply and

speakers if the fuse of the separately sold battery

wire or the amplifier fuse blows. Detect the cause

and solve the problem, then replace the fuse with

another one of the same size and rating.

• To prevent malfunction of the amplifier and

speakers, the protective circuit will cut the power

supply to the amplifier (sound will stop) when an

abnormal condition occurs. In such a case, switch

the power to the system OFF and check the

connection of the power supply and speakers.

Detect the cause and solve the problem.

• Contact the dealer if you cannot detect the cause.

• To prevent an electric shock or short-circuit

during connection and installation, be sure to

disconnect the negative (–) terminal of the battery

beforehand.

• Confirm that no parts are behind the panel when

drilling a hole for installation of the amplifier. Be

sure to protect all cables and important equipment

such as fuel lines, brake lines and the electrical

wiring from damage.

• DO NOT allow amplifier to come into contact

with liquids due to, for example, the location

where the amplifier is installed. Electrical shock

could result. Also, amplifier and speaker damage,

smoke, and overheating could result from contact

with liquids. In addition, the amplifier surface and

the surface of any attached speakers could become

hot to the touch and minor burns could result.

Diagram A - Proper

Ohm

Speaker

Ohm

Speaker

Pioneer

Amplifier

4 Ohm Bridged Mode

L+ R-

Diagram B - Improper

Ohm

Speaker

Ohm

Speaker

Pioneer

Amplifier

2 Ohm Bridged Mode

L+ R-

Before Using This Product <ENGLISH>

Published by Pioneer Corporation.

Publicado por Pioneer Corporation.

Printed in China

Impreso na China

<YRD5067-A/U> ES<KMINX> <05L00000>

BRIDGEABLE FOUR-CHANNEL

POWER AMPLIFIER

AMPLIFICADOR DE POTENCIA DE

CUATRO CANALES EN PUENTE

Owner’s Manual

PRS-D4000F

Manual del Propietario

PIONEER CORPORATION

4-1, MEGURO 1-CHOME, MEGURO-KU, TOKYO 153-8654, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

178-184 Boundary Road, Braeside, Victoria 3195, Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS OF CANADA, INC.

300 Allstate Parkway, Markham, Ontario L3R OP2, Canada

TEL: 1-877-283-5901

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso

Col.Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

Gain Control

Adjusting the gain controls A and B will help match the output of the car stereo to the Pioneer

amplifier. Normally, set the gain controls to the NORMAL position. If the output is low, even

when the volume of the car stereo is turned up, turn these controls clockwise. If there is dis-

tortion when the volume of the car stereo is turned up, turn these controls counter-clockwise.

• If you only use one input plug, set the gain controls for speaker outputs A and B to the same position.

• When using with an RCA equipped car stereo (standard output of 500 mV), set to the NORMAL

position. When using with an RCA equipped Pioneer car stereo with max. output of 4 V or more,

adjust level to match the car stereo output level.

Power Indicator

The power indicator lights when the

power is switched on.

Input Select Switch

For two-channel input, slide this switch

to the left. For four-channel input, slide

this switch to the right.

Cut Off Frequency Control

If the LPF/HPF select switch is set to

LPF or HPF, you can select a cut off

frequency from 40 Hz to 120 Hz.

BFC (Beat Frequency Control)

Switch

BFC switch is on the bottom of the unit.

If you hear a beat while listening to an

AM broadcast with your car stereo,

change the BFC switch using a small

standard tip screwdriver.

Terminal Cover

Before setting up the unit, unfasten the

screws with a 4 mm hexagonal wrench

(not supplied) and remove the terminal

cover.

LPF (Low-Pass Filter)/HPF (High-Pass Filter) Select Switch

Set the LPF/HPF select switch as follows according to the type of speaker that is connected

to the speaker output connector and the car stereo system:

LPF/HPF Select Audio frequency range Speaker Remarks

Switch to be output Type

LPF (Left) * — 40 Hz to 120 Hz Subwoofer Connect a subwoofer.

OFF (Center) Full range Full range

HPF (Right) * 40 Hz to 120 Hz — Full range Use if you want to cut the

very low frequency range*

because it is not necessary

for the speakers you are

using.

* See the “Cut Off Frequency Control” section.

Input Switch

It is possible to input from a car stereo

external output (subwoofer output) or a

car stereo speaker output. When using

an external output (subwoofer output),

slide the switch to the left. For connec-

tion instructions, see the “Connection

Diagram” section. When using a speak-

er output, slide the switch to the right.

In this case, it is necessary to use the

supplied speaker input wire with RCA

pin cord. For details, see the “Using the

Speaker Input” section.

1 2 3 4 5 6

Résumé du contenu

Page 1 - PRS-D4000F

Setting the Unit <ENGLISH>Thank you for purchasing this PIONEERproduct. Before attempting operation, besure to read this manual.In case of troub

Page 2 - Using the Speaker Input

Connecting the Power Terminal• Always use the special red battery and groundwire [RD-223], which is sold separately. Connectthe battery wire directly

Page 3 - Replacing the terminal cover

Connecting the Unit <ENGLISH>CAUTION• Do not install in:—Places where it could injure the driver or pas-sengers if the vehicle stops suddenly.—P

Page 4 - Diagrama B - Incorrecto

Ajuste de esta unidad <ESPAÑOL>Antes de usar este producto <ESPAÑOL>Muchas gracias por la adquisición de esteproducto PIONEER. Antes de tr

Page 5

Conexión del terminal de alimentación• Siempre utilice el cable de batería rojo especial yel cable de tierra [RD-223], vendidos separada-mente. Conect

Page 6 - Ejemplo de instalación en la

PRECAUCION• No lo instale en:— Donde podría lesionar al conductor o a lospasajeros si se detiene el vehículo bruscamente.— Donde podría interferir con

Commentaires sur ces manuels

Pas de commentaire

Pioneer Premier PRS-D4000F Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Amplificateurs audio pour voitures Pioneer Premier PRS-D4000F. Pioneer Premier PRS-D4000F User's Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio pour voitures Pioneer Premier PRS-D4000F