Pioneer SPEAKER DEQ-P8000 Manuel d'utilisateur télécharger pdf

Connecting to a sold separately power amp

This product can be connected to a sold separately power amp using the RCA output jacks.

This product

Blue/white

To system control terminal of the power

amp or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

≠

Front speaker Front speaker

Rear speaker Rear speaker

Center speaker Subwoofer

System remote control

RCA cables

(sold separately)

Power amp

(sold separately)

Subwoofer output

Rear output

Front output

Center output

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

When you connect a power amp (sold

separately), be sure to use the blue/white

lead of this unit. If you use the blue/white

lead of the head unit, it causes noises.

40cm

(1 ft. 3-3/4 in.)

Connecting the power cord

Noise filter

Lock tie

Noise filter

Gray/blackWhite/black

Green Violet

Left Right

White

Gray

Green/black Violet/black

Front speaker Front speaker

Rear speaker Rear speaker

This product

Yellow

To terminal always supplied with

power regardless of ignition switch

position.

Fuse holder

Black (ground)

To vehicle (metal) body.

Blue/white

To system control terminal of the power

amp or Auto-antenna relay control terminal

(max. 300 mA 12 V DC).

Do not connect anything to the speaker

leads that are not connected to speakers.

When you connect a power amp (sold

separately), be sure to use the blue/white

lead of this unit. If you use the blue/white

lead of the head unit, it causes noises.

Black

Black/white

Center speaker

≠

40cm

(1 ft. 3-3/4 in.)

Note:

• This unit is for vehicles with a 12-volt battery

and negative grounding. Before installing it in a

recreational vehicle, truck, or bus, check the bat-

tery voltage.

• To avoid shorts in the electrical system, be sure

to disconnect the · battery cable before begin-

ning installation.

• Refer to the owner’s manual for details on con-

necting the power amp and other units, then

make connections correctly.

• Secure the wiring with cable clamps or adhesive

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• Route and secure all wiring so it cannot touch

any moving parts, such as the gear shift, hand-

brake and seat rails. Do not route wiring in

places that get hot, such as near the heater outlet.

If the insulation of the wiring melts or gets torn,

there is a danger of the wiring short-circuiting to

the vehicle body.

• Don’t pass the yellow lead through a hole into

the engine compartment to connect to the battery.

This will damage the lead insulation and cause a

very dangerous short.

• Do not shorten any leads. If you do, the protec-

tion circuit may fail to work when it should.

• Never feed power to other equipment by cutting

the insulation of the power supply lead of the

unit and tapping into the lead. The current capac-

ity of the lead will be exceeded, causing over-

heating.

• When replacing fuse, be sure to use only fuse of

the rating prescribed on the fuse holder.

• Since a unique BPTL circuit is employed, never

wire so the speaker leads are directly grounded

or the left and right · speaker leads are com-

mon.

• Speakers connected to this unit must be high-

power types with minimum rating of 50 W and

impedance of 4 to 8 ohms. Connecting speakers

with output and/or impedance values other than

those noted here may result in the speakers

catching fire, emitting smoke or becoming dam-

aged.

• When this product’s source is switched ON, a

control signal is output through the blue/white

lead. Connect to an external power amp’s system

remote control or the car’s Auto-antenna relay

control terminal (max. 300 mA 12 V DC). If the

car features a glass antenna, connect to the anten-

na booster power supply terminal.

• When an external power amp is being used with

this system, be sure not to connect the blue/white

lead to the amp’s power terminal. Likewise, do

not connect the blue/white lead to the power ter-

minal of the auto-antenna. Such connection could

cause excessive current drain and malfunction.

• To avoid short-circuiting, cover the disconnected

lead with insulating tape. Especially, insulate the

unused speaker leads without fail. There is a pos-

sibility of short-circuiting if the leads are not

insulated.

• To prevent incorrect connection, the input side of

the IP-BUS or optical cable connector is blue,

and the output side is black. Connect the connec-

tors of the same colors correctly.

• If this unit is installed in a vehicle that does not

have an ACC (accessory) position on the ignition

switch, the red lead of the unit should be con-

nected to a terminal coupled with ignition switch

ON/OFF operations. If this is not done, the vehi-

cle battery may be drained when you are away

from the vehicle for several hours.

• The black lead is ground. Please ground this lead

separately from the ground of high-current prod-

ucts such as power amps.

If you ground the products together and the

ground becomes detached, there is a risk of dam-

age to the products or fire.

• To ensure proper heat dissipation of this product,

take special care not to block the cooling fan side

of this product.

No ACC positionACC position

Connecting the Units <ENGLISH>

• Cords for this product and those for other prod-

ucts may be different colors even if they have

the same function. When connecting this prod-

uct to another product, refer to the supplied

manuals of both products and connect cords that

have the same function.

INSTALLATION MANUAL

MANUEL D’INSTALLATION

DEQ-P8000

Printed in Japan

Imprimé au Japon

<CRD3878-A> UC

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit

est conforme à CEMA.

1 2 3 4 5 6

Résumé du contenu

Page 1 - MANUEL D’INSTALLATION

Connecting to a sold separately power ampThis product can be connected to a sold separately power amp using the RCA output jacks.This productBlue/whit

Page 2 - Connecting the system

Connecting the systemConnecting the Units <ENGLISH>YellowGuide speaker output(GUIDE SP OUTPUT)21 pin cableAV Receiver/DVD player(AVH-P6600DVD)(s

Page 3 - Installation <ENGLISH>

Routing the optical cablePrecaution:• Try not to bend the optical cable sharply. If it isnecessary to bend it sharply, make sure that thebending radiu

Page 4 - Remarque:

Raccordement à un amplificateur vendu séparémentCet appareil peut être relié à un amplificateur vendu séparément; utilisez pour cela les prises de sor

Page 5 - Raccordement du système

Raccordement du systèmeConnexion des appareils <FRANÇAIS>Entrée pour câbleà 26 brochesBoîte de raccordement de câbleà fibres optiques (fourni)Ha

Page 6 - Installation <FRANÇAIS>

Cheminement du câble optiquePrécaution:• Veillez à ce que le câble optique ne forme pas uncoude serré. S’il est nécessaire que le câbleoptique forme u

Commentaires sur ces manuels

Pas de commentaire

Pioneer SPEAKER DEQ-P8000 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Acoustique Pioneer SPEAKER DEQ-P8000. Pioneer SPEAKER DEQ-P8000 Manuel d'utilisation Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Acoustique Pioneer SPEAKER DEQ-P8000