Pioneer DJM-T1 Manuel d'utilisateur télécharger pdf (Page 27)

100

English

Changing this unit’s settings

1 Press the [UTILITY (WAKE UP)] button for over 1 second.

The [UTILITY (WAKE UP)] indicator and the top of the [CH 1] channel level indicator

flash.

2 Press the [LOAD (DUPLICATE) B] button.

The setting item changes each time the [LOAD (DUPLICATE) B] button is pressed.

The flashing position of the [CH 1] channel level indicator moves downwards.

! When the [LOAD (DUPLICATE) A] button is pressed, the selection returns to the

previous setting item.

The flashing position of the [CH 1] channel level indicator moves upwards.

3 Turn the rotary selector.

Change the setting value.

! When the setting value can be switched on and off

— On: The green section of the [CH 2] channel level indicator lights.

— Off: The green section of the [CH 2] channel level indicator turns off.

! When the setting value can be switched in steps

— One’s place of setting value: Value indicated by the number of segments

of the [CH 2] channel level indicator that are lit.

— Ten’s place of setting value: Value indicated by the number of segments

of the master level indicator that are lit.

4 Press the rotary selector.

The settings are stored in this unit.

The [UTILITY (WAKE UP)] button flashes rapidly. Do not turn this unit’s power off

while the settings are being stored.

! Storing is completed when the [UTILITY (WAKE UP)] button switches from

flashing rapidly to flashing normally.

! Press the [UTILITY (WAKE UP)] button to return to normal operation.

About the auto standby function

When [Auto Standby] is set to [ON], the standby mode is set automatically if 4

hours pass with all of the conditions shown below met.

— That none of this unit’s buttons or controls are operated.

— That no audio signals are input to this unit’s input terminals.

— That no computer is connected by USB.

! When the [UTILITY (WAKE UP)] button is pressed, the standby mode is

canceled.

! This unit is shipped with the auto standby function turned on. If you do not want

to use the auto standby function, set [Auto Standby] to [OFF].

Checking the firmware version

1 Press the [UTILITY (WAKE UP)] button for over 1 second.

2 Press the [LOAD (DUPLICATE) A] button.

The firmware version is indicated by the segments of the channel level and master

level indicators that light.

— Number of segments of the [CH 1] channel level indicator lit: One’s place

— Number of segments of the master channel level indicator lit: First decimal

place

— Number of segments of the [CH 2] channel level indicator lit: Second deci-

mal place

Example: When version “1.07” is indicated

MASTER1

OVER

! If the top segment of the [CH 1] channel level indicator flashes, the firmware

version is one earlier than 2.00.

Setting preferences

Options settings

Flashing position of [CH 1]

channel level indicator

Setting value Default value Descriptions

Cross Fader Cut Lag

Very top 0 to 52

Adjusts the play at the edges of the crossfader (the cut lag). The cut lag can be

adjusted between 0.74 mm and 5.94 mm, in 0.1 mm units.1

Cross Fader Curve Slow A

Second from top 0 to 32

Adjusts the [CH 1] side attenuation curve characteristics when the [CROSS F.

CURVE (THRU,

, )] switch is set to [ ].2

Cross Fader Curve Slow B

Third from top 0 to 32

Adjusts the [CH 2] side attenuation curve characteristics when the [CROSS F.

CURVE (THRU,

, )] switch is set to [ ].2

Cross Fader Curve Fast A

Fourth from top 0 to 32

Adjusts the [CH 1] side attenuation curve characteristics when the [CROSS F.

CURVE (THRU,

, )] switch is set to [ ].2

Cross Fader Curve Fast B

Fifth from top 0 to 32

Adjusts the [CH 2] side attenuation curve characteristics when the [CROSS F.

CURVE (THRU,

, )] switch is set to [ ].2

Generic Controller Mode

Sixth from top ON/OFF

OFF

Turns on and off the function for selecting effects using the effect control

buttons.

When off, the LFO CONTROL and CROSS FADER CONTROL functions can be

used.

Mic Output To Booth Monitor

Seventh from top ON/OFF

Sets whether or not to output the microphone’s audio signals from [BOOTH]

terminals.

Auto Standby

Eighth from top ON/OFF

Turns the auto standby function on and off.

1 If the setting value is extremely small, the sound may not be completely muted even when the crossfader is positioned at the very edge.

2 If the setting value is small, the attenuation will have a gentle curve characteristic. If the setting value is large, the attenuation will have an abrupt curve characteristic.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 99 100

Commentaires sur ces manuels

Pas de commentaire

Pioneer DJM-T1 Manuel d'utilisateur Page 27

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour la musique Pioneer DJM-T1